E1407A Datasheet, PDF (1/2 Pages) Keysight Technologies – A/B to C-Size P1/P2 Active Adapter

Agilent E1407A
A/B to C-Size P1/P2
Active Adapter
Data sheet
• Adapts A- or B-size VXI to C-size VXI
• Provides active extensions of P1 and P2
• Fits 1-slot or 2-slots (optional) modules
• Provides slave-only capability
• Allows isolation of outer rows of P2
Description
The Agilent Technologies E1407A C-size, 1- or 2-slot carrier adapts
A- or B-size VXI modules for use in all C-size VXI mainframes. The P1
and P2 extensions are fully buffered. A ribbon cable allows isolation
of the outer rows of P2 for VME applications. The E1407A provides
slave-only capability and cannot be used in Slot 0 or with bus masters.
The standard module is 1-slot wide; Option 010 is 2 slots wide, however,
it only connects to the backplane on the left-most slot. Any number of
adapters can be used in an Agilent VXI mainframe.
Many (but not all) VME cards can be adapted for the use in VXI
mainframes using this module if they meet VXI mechanical and electrical
restrictions. However, this is not a supported configuration.
Refer to the Agilent Technologies Website for instrument driver avail-
ability and downloading instructions.
Cables
Cables are required for adapting B-size multiplexers in a C-size main-
frame. The B-size multiplexers require analog bus cables longer than
those shipped, and, therefore, longer ones must be ordered separately
to connect Multiplexer-to-Multiplexer and Multiplexer to the Agilent
E1411A/B C-size digital multimeter. These cables are necessary when
mounting a B-size multimeter in a C-size adapter because of the different
spacing and positioning of the analog bus connectors on the B- and
C-size modules. The following cables are available:
1. Agilent E1411A/B DMM to B-size Multiplexer/E1407A Cable
part numbers:
Agilent E1326-61611 Analog Bus Cable, The E1326-61611 is the same
cable used with the B-size cardcage internal DMM configuration.
• Agilent E1411-61601 Multiplexer-to-DMM (FET Multiplexer only).
Order the Agilent E1411-80001 cable kit to get both the E1326-61611
long analog bus cable and the E1411-61601 digital bus cable together.
2. B-size Multiplexer/E1407A to B-size Multiplexer/E1407A Cable
part numbers:
• Agilent E1400-61605 Multiplexer-to-Multiplexer Cable. The E1400-
61605 is the same cable used to connect C-size Multiplexers together.
• Agilent E1411-61601 Multiplexer-to-DMM (FET Multiplexer only).
Order the Agilent E1411-80001 cable kit to get both the E1326-61611
long analog bus cable and the E1411-61601 digital bus cable together.
3. C-size Multiplexer to B-size Multiplexer/E1407A Cable
part numbers:
Agilent E1326-61611 Analog Bus Cable. The E1326-61611 is the same
cable used with the B-size cardcage internal DMM configuration.
• Agilent E1411-61601 Multiplexer-to-DMM (FET Multiplexer only).
Order the Agilent E1411-80001 cable kit to get both the E1326-61611
long analog bus cable and the E1411-61601 digital bus cable together.
General Specifications
VXI Characteristics
VXI device type
Size
Slots
Connectors
Shared memory
VXI buses
Module Current
+5 V
+12 V
–12 V
+24 V
–24 V
–5.2 V
–2 V
n/a
C
1/2
P1 or 2
n/a
n/a
I_PM
0.1
0.07
0
0
0
0
0.01
Cooling/Slot
Watts/Slot
0.50
∆P mm H₂O
0.20
Air Flow liter/s
0.10
Ordering Information
Description
A/B-to-C-Size Adapter
2-Slot Wide Adapter
I_OM
0.01
0.01
0
0
0
0
0
Product No.
E1407A
E1407A 010