MBRF2535CT Datasheet, PDF (1/2 Pages) General Semiconductor – SCHOTTKY ISOLATED PLASTIC RECTIFIER

MBRF2535CT THRU MBRF2560CT
0.405 (10.27)
0.383 (9.72)
ITO-220AB
ITO-220AB
0.140 (3.56)
DIA.
0.130 (3.30)
0.600 (15.5)
0.580 (14.5)
0.560 (14.22)
0.530 (13.46)
PIN
1
2
3
0.676 (17.2)
0.646 (16.4)
0.191 (4.85)
0.171 (4.35)
0.060 (1.52)
0.350 (8.89)
0.330 (8.38)
0.188 (4.77)
0.172 (4.36)
0.110 (2.80)
0.100 (2.54)
0.131 (3.39)
DIA.
0.122 (3.08)
0.110 (2.80)
0.100 (2.54)
0.205 (5.20)
0.195 (4.95)
0.037 (0.94)
0.027 (0.69)
0.105 (2.67)
0.095 (2.41)
PIN 1
PIN 3
0.022 (0.55)
0.014 (0.36)
PIN 2
Dimensions in inches and (millimeters)
FEATURES
¨ Isolated plastic package has Underwriters Laboratory
Flammability Classifications 94V-0
¨ Dual rectifier construction, positive center-tap
¨ Metal silicon junction, majority carrier conduction
¨ Low power loss, high efficiency
¨ High current capability, low forward voltage drop
¨ High surge capability
¨ For use in low voltage, high frequency inverters,
free wheeling, and polarity protection applications
¨ Guardring for overvoltage protection
¨ High temperature soldering guaranteed:
250°C/10 seconds, 0.25" (6.35mm) from case
MECHANICAL DATA
Case: ITO-220AB fully overmolded plastic body
Terminals: Lead solderable per MIL-STD-750,
Method 2026
Polarity: As marked
Mounting Position: Any
Weight: 0.08 ounce, 2.24 grams
Mounting Torque: 5 in. - lbs. max.
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25¡C ambient temperature unless otherwise specified.
Maximum repetitive peak reverse voltage
Maximum working peak reverse voltage
Maximum DC blocking voltage
Maximum average forward rectified current at TC=130¡C
Peak repetitive forward current per leg at TC=130¡C
(rated VR, square wave, 20 KHZ)
Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load (JEDEC Method)
SYMBOLS MBRF2535CT MBRF2545CT MBRF2550CT
VRRM
35
45
50
VRWM
35
45
50
VDC
35
45
50
I(AV)
30.0
MBRF2560CT
60
60
60
UNITS
Volts
Volts
Volts
Amps
IFRM
30.0
Amps
IFSM
150.0
Amps
Peak repetitive reverse surge current (NOTE 1)
Maximum instantaneous forward voltage IF=15.0A ,TC=25¡C
per leg at: (NOTE 2)
IF=15.0A ,TC=25¡C
IF= 30A, TC=25¡C
IF= 30A, TC=125¡C
Maximum instantaneous reverse current at
rated DC blocking voltage per leg (NOTE 2)
TC=25¡C
TC=125¡C
Maximum thermal resistance (NOTE 3)
Voltage rate of change (rated VR)
Operating junction temperature range
Storage temperature range
RMS Isolation voltage from terminals to heatsink
with RH ² 30%
IRRM
VF
IR
RQJC
dv/dt
TJ
TSTG
VISOL
1.0
-
-
0.82
0.73
0.2
40.0
4.5
10,000
-65 to +150
-65 to +175
4500 (NOTE 4)
3500 (NOTE 5)
1500 (NOTE 6)
0.5
0.75
0.65
-
-
1.0
50.0
Amps
Volts
mA
¡C/W
V/ms
¡C
¡C
Volts
NOTES: (1) 2.0ms pulse width, f=1.0 KHZ
(2) Pulse test: 300ms pulse width, 1% duty cycle
(3) Thermal resistance from junction to case per leg
(4) Clip mounting (on case), where lead does not overlap heatsink with 0.110Ó offset.
(5) Clip mounting (on case), where leads do overlap heatsink.
(6) Screw mounting with 4-40 screw, where washer diameter is £ 4.9 mm (0.19Ó).
2/18/99
www.kersemi.com