MBRF2035CT Datasheet, PDF (1/2 Pages) General Semiconductor – SCHOTTKY ISOLATED PLASTIC RECTIFIER

MBRF2035CT THRU MBRF2060CT
0.405 (10.27)
0.383 (9.72)
ITO-220AB
0.140 (3.56)
DIA.
0.130 (3.30)
0.600 (15.5)
0.580 (14.5)
0.560 (14.22)
0.530 (13.46)
PIN
1
2
3
0.676 (17.2)
0.646 (16.4)
0.191 (4.85)
0.171 (4.35)
0.060 (1.52)
0.350 (8.89)
0.330 (8.38)
0.188 (4.77)
0.172 (4.36)
0.110 (2.80)
0.100 (2.54)
0.131 (3.39)
0.122 (3.08) ^DIA.
0.110 (2.80)
0.100 (2.54)
0.205 (5.20)
0.195 (4.95)
0.037 (0.94)
0.027 (0.69)
0.105 (2.67)
0.095 (2.41)
PIN 1
0.022 (0.55)
0.014 (0.36)
PIN 2
PIN 3
Dimensions in inches and (millimeters)
FEATURES
¨ Isolated plastic package has Underwriters Laboratory
Flammability Classification 94V-0
¨ Dual rectifier construction, positive center tap
¨ Metal silicon junction,majority carrier conduction
¨ Low power loss, high efficiency
¨ High current capability, low forward voltage drop
¨ High surge capability
¨ Guardring for overvoltage protection
¨ For use in low voltage, high frequency inverters,
free wheeling, and polarity protection applications
¨ High temperature soldering guaranteed:
250°C/10 seconds, 0.25" (6.35mm) from case
MECHANICAL DATA
Case: ITO-220AB fully overmolded plastic body
Terminals: Leads solderable per MIL-STD-750,Method 2026
Polarity: As marked
Mounting Position: Any
Weight: 0.08 ounce, 2.24 grams
Mounting Torque: 5 in. - lbs.max.
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25¡C ambient temperature unless otherwise specified.
Maximum repetitive peak reverse voltage
Maximum working peak reverse voltage
Maximum DC blocking voltage
Maximum average forward rectified current
at TC=135¡C
Peak repetitive forward current per leg at TC=135¡C
(rated VR, sq. wave 2.0 KHZ)
Peak forward surge current 8.3ms single half sine-
wave superimposed on rated load (JEDEC Method)
Peak repetitive reverse surge current (NOTE 1)
Maximum instantaneous
forward voltage per leg at
(NOTE 2)
IF=10A, TC=25¡C
IF=10A, TC=125¡C
IF=20A, TC=25¡C
IF=20A, TC=125¡C
Maximum instantaneous reverse current at
rated DC blocking voltage per leg TC=25¡C
TC=125¡C
Voltage rate of change, (rated VR)
Typical thermal resistance per leg (NOTE 3)
Operating junction temperature range
Storage temperature range
RMS Isolation voltage from terminals to heatsink
with RH ² 30%
SYMBOLS
VRRM
VRWM
VDC
MBRF2035CT
35
35
35
MBRF2045CT
45
45
45
MBRF2050CT MBRF2060CT
50
60
50
60
50
60
UNITS
Volts
Volts
Volts
I(AV)
20.0
Amps
IFRM
20.0
Amps
IFSM
IRRM
VF
150.0
1.0
0.5
_
0.80
0.57
0.70
0.84
0.95
0.72
0.85
Amps
Amps
Volts
IR
dv/dt
RQJC
TJ
TSTG
VISOL
0.1
15.0
10,000
5.0
-65 to +150
-65 to +175
4500 (NOTE 4)
3500 (NOTE 5)
1500 (NOTE 6)
0.15
150.0
mA
V/ms
¡C/W
¡C
¡C
Volts
NOTES: (1) 2.0ms pulse width, f=1.0KHZ
(2) Pulse test: 300ms pulse width, 1% duty cycle
(3) Thermal resistance from junction to case per leg
(4) Clip mounting (on case), where lead does not overlap heatsink with 0.110Ó offset.
(5) Clip mounting (on case, where leads do overlap heatsink.
(6) Screw mounting with 4-40 screw, where washer diameter is £ 4.9 mm (0.19Ó).
2/18/99
www.kersemi.com