MBRF1535CT Datasheet, PDF (1/2 Pages) General Semiconductor – SCHOTTKY ISOLATED PLASTIC RECTIFIER

MBRF1535CT THRU MBRF1560CT
0.405 (10.27)
0.383 (9.72)
ITO-220AB
0.140 (3.56)
DIA.
0.130 (3.30)
0.600 (15.5)
0.580 (14.5)
0.560 (14.22)
0.530 (13.46)
PIN
1
2
3
0.676 (17.2)
0.646 (16.4)
0.191 (4.85)
0.171 (4.35)
0.060 (1.52)
0.350 (8.89)
0.330 (8.38)
0.188 (4.77)
0.172 (4.36)
0.110 (2.80)
0.100 (2.54)
0.131 (3.39)
0.122 (3.08) ^DIA.
0.110 (2.80)
0.100 (2.54)
0.205 (5.20)
0.195 (4.95)
0.037 (0.94)
0.027 (0.69)
0.105 (2.67)
0.095 (2.41)
PIN 1
0.022 (0.55)
0.014 (0.36)
PIN 2
PIN 3
Dimensions in inches and (millimeters)
FEATURES
¨ Isolated plastic package has Underwriters Laboratory
Flammability Classifications 94V-0
¨ Metal silicon junction, majority carrier conduction
¨ Low power loss, high efficiency
¨ High current capability, low forward voltage drop
¨ High surge capability
¨ For use in low voltage, high frequency inverters,
free wheeling, and polarity protection applications
¨ Dual rectifier construction, positive center tap
¨ Guardring for transient protection
¨ High temperature soldering guaranteed:
250¡C/10 seconds, 0.25" (6.35mm) from case
MECHANICAL DATA
Case: ITO-220AB fully overmolded plastic body
Terminals: Leads solderable per MIL-STD-750, Method 2026
Polarity: As marked
Mounting Position: Any
Mounting Torque: 5 in. - lbs. max.
Weight: 0.08 ounces, 2.24 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25¡C ambient temperature unless otherwise specified.
SYMBOLS MBRF1535CT MBRF1545CT MBRF1550CT MBRF1560CT UNITS
Maximum repetitive peak reverse voltage
Maximum working peak reverse voltage
Maximum DC blocking voltage
Maximum average forward rectified current
at TC=105¡C
Peak repetitive forward current at TC=105¡C per diode
(rated VR, 20KHZ sq.wave)
Peak forward surge current 8.3ms single half sine-
wave superimposed on rated load (JEDEC method)
VRRM
35
VRWM
35
VDC
35
I(AV)
IFRM
IFSM
45
50
45
50
45
50
15.0
15.0
150.0
60
Volts
60
Volts
60
Volts
Amps
Amps
Amps
Peak repetitive reverse surge current (NOTE 1)
Maximum instantaneous forward voltage
per leg at
(NOTE 2)
IF=7.5A,TC=25¡C
IF=7.5A,TC=125¡C
IF=15A,TC=25¡C
IF=15A,TC=125¡C
Maximum instantaneous reverse current at rated
DC blocking voltage per leg
TC=25¡C
(NOTE 2) TC=125¡C
Voltage rate of change, (rated VR)
Maximum thermal resistance per leg (NOTE 3)
Operating junction temperature range
Storage temperature range
RMS Isolation voltage from terminals to heatsink
with RH ² 30%
IRRM
VF
IR
dv/dt
RQJC
TJ
TSTG
VISOL
1.0
0.5
_
0.75
0.57
0.84
0.72
0._65
_
0.1
15.0
10,000
5.0
-65 to +150
-65 to +175
4500 (NOTE 4)
3500 (NOTE 5)
1500 (NOTE 6)
1.0
50.0
Amps
Volts
mA
V/ms
¡C/W
¡C
¡C
Volts
NOTES: (1) 2.0ms pulse width, f=1.0 KHZ
(2) 300ms, pulse width, 1% duty cycle
(3) Thermal resistance from junction to case
(4) Clip mounting (on case), where lead does not overlap heatsink with 0.110Ó offset.
(5) Clip mounting (on case), where leads do overlap heatsink.
(6) Screw mounting with 4-40 screw, where washer diameter is £ 4.9 mm (0.19Ó).
www.kersemi.com
2/18/99