CSRXXB565KM Datasheet, PDF (3/38 Pages) Kemet Corporation – TANTALUM HERMETICALLY SEALED

TANTALUM HERMETICALLY SEALED / AXIAL — MIL-PRF-39003
T110 SERIES — POLAR TYPE, T212 (CSR13)
KEMET standard hermetic sealed T110 Series are desirable for use in high humidi-
ty environments. They are ruggedly built, designed for miniaturized circuitry, and are
especially suited for coupling, bypass, filtering and R-C timing circuits. They exhibit
excellent stability, extremely low DC leakage current, dissipation factor, and
ESR/impedance over a wide temperature and frequency range.
Available in standard EIA capacitance values from .0047-330 µF in ±20%, ±10%, and ±5%
tolerances and working voltages from 6-125 VDC.
Higher CV values in comparable case sizes are available in KEMET T140 Series.
Refer to page 27.
Included in the following Series table is a complete listing of CSR13 qualified MIL-
PRF-39003 capacitors. KEMET is approved to manufacture the S (0.001%/k hrs.)
Exponential & D (0.001%/k hrs.) Graded failure rate levels.
KEMET is now offering low ESR limits in the T110 Series. See ESR chart on page
19. You may order the lower ESR by using Customer Specification 2864 as the last
four digits of the part number.
Effective September 30, 2005, the KEMET T110 Series is RoHS Compliant.
CAPACITOR OUTLINE DRAWINGS
1.50±.250
L
1.50±.250
D
(38.10±6.35)
(38.10±6.35)
+
B
C
DIMENSIONS — INCHES & (MILLIMETERS)
UNINSULATED
CASE
SIZE
D
±0.005
±(.13)
L
±0.031
±(.79)
A
0.125
(3.18)
0.250
(6.35)
B
0.175
(4.45)
0.438
(11.13)
C
0.279
(7.09)
0.650
(16.51)
D
0.341
(8.66)
0.750
(19.05)
INSULATED
D
±0.010
±(.25)
L
±0.031
±(.79)
0.135
(3.43)
0.286
(7.26)
0.185
(4.70)
0.474
(12.04)
0.289
(7.34)
0.686
(17.42)
0.351
(8.92)
0.786
(19.96)
B
±0.002
±(.05)
0.020
(.51)
0.020
(.51)
0.025
(.64)
0.025
(.64)
C
MAX.
0.422
(10.72)
0.610
(15.49)
0.822
(20.88)
0.922
(23.42)
ORDERING INFORMATION*
T XXX A 105 K 050 A S C
TANTALUM
SERIES
T110, T212 (CSR13)
T111, T213 (CSR91)
T140, T242 (CSR23)
SPECIFICATION
All capacitors are sleeved
unless specified.
CASE SIZE
A/ B / C / D
PICOFARAD CODE
First two digits represent significant figures.
Third digit specifies number of zeros to follow.
LEAD MATERIAL
S — Standard
T – 100% Tin (T110, T140 Series only)
CAPACITANCE TOLERANCE
M — ±20% K — ±10% J — ±5%
FAILURE RATE**
GRADED
EXPONENTIAL
VOLTAGE
At 85°C
A — Not Applicable M — 1%/k hrs.
B — 0.1%/k hrs.
P — 0.1%/k hrs.
**Part Number Example: T110A105K050AS (14 digits - no spaces)
*For Military Ordering Information, see page 4.
C — 0.01%/k hrs. R — 0.01%/k hrs.
D — 0.001%/k hrs. S — 0.001%/k hrs.
**Failure Rates apply only to military products.
MARKING INFORMATION
Marking: Unless otherwise specified by special order, standard marking of T110 Series capacitor consists of the following:
A, B, C & D CASES
+K 10%
R56 µF
100V
0312
Polarity, Manufacturer’s Identification and Capacitance Tol.
Nominal Capacitance — (µF) (“R” indicates decimal)
Voltage
Date Code (e.g.: 0312)
* For Military Marking, see page 4.
6
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 [phone]