F9033 Datasheet, PDF (2/3 Pages) Kemet Corporation – Surface Mount Tip & Ring Ceramic Chip Capacitors

Capacitor Ordering Information
Style
C - Ceramic
C 0805 C 103 K
Size Code
0805, 1206, 1210, 1812, 1825, 2220, 2225
Specification
C - Standard
Capacitance Code, pF
First two digits represent significant figures.
Third digit specifies number of zeros. 100 pF = 101.
Capacitance Tolerance
J = ±5%, K = ±10%, M = ±20%
A
R
AC
End Metallization
C = 100% Sn Std.
Failure Rate Level
A = Not Applicable
Temperature Characteristic
Designated by Capacitance
Change over Temperature Range
R – X7R (±15%) (-55°C +125°C)
Voltage
A = 250V
General Performance Characteristics & Electrical Parameters 250 VDC
EIA Case Sizes
Capacitance Range
Test Parameters
Operating Temperature Range
Temperature Characteristic
Capacitance Tolerances
Dissipation Factor
Aging Rate
Voltage Rating
25°C IR @ Rated Voltage
Dielectric Strength (DMV)
0805, 1206, 1210, 1812, 1825, 2220, 2225
0.001μF to 1.2μF
Capacitance and Dissipation Factor measured at 1.0 ± 0.2 Vrms and 1.0 ± 0.2 kHz
-55°C to +125°C
-55°C to +125°C X7R: ±15% (0% VDC)
J = ±5%, K = ±10%, M = ±20%
≤2.5%
2.5% per decade hour
250 VDC
1000MΩ−μF or 100GΩ, whichever is less
250% of Rated Voltage 5 ± 1 seconds and charge/discharge not exceeding 50mA
Marking
These chips are supplied unmarked. If required, they can be laser-marked as an extra cost option. Details on the
marking format are included in KEMET Surface Mount Catalog F3102 on page 96.
Soldering Process
The 0805 and 1206 sizes are suitable for either reflow or wave soldering. Sizes 1210 and larger should be limited
to reflow soldering only. All sizes incorporate the standard KEMET barrier layer of pure nickel with an overplating
of pure tin for excellent solderability and resistance to leaching of the termination.
Packaging
KEMET High Voltage Surface Mount MLCC capacitors are available packaged in tape and reel configuration.
Recommended Solder Pad Dimensions
T - Total Length S - Separation W - Pad Width L - Pad Length
Chip Size
mm
in.
mm in. mm in. mm in.
0805 3.30 0.130 0.70 0.028 1.60 0.063 1.30 0.051
1206 4.50 0.177 1.50 0.059 2.00 0.079 1.50 0.059
1210 4.50 0.177 1.50 0.059 2.90 0.114 1.50 0.059
1812 5.90 0.232 2.30 0.091 3.70 0.146 1.80 0.071
1825 5.90 0.232 2.30 0.091 6.90 0.272 1.80 0.071
2220 7.00 0.276 3.30 0.130 5.50 0.217 1.85 0.073
2225 7.00 0.276 3.30 0.130 6.80 0.268 1.85 0.073
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • [phone] • www.kemet.com