JFYE Datasheet, PDF (1/2 Pages) jb Capacitors Company – Box Type Met Polypropylene Film Capacitor

Box Type Met Polypropylene Film Capacitor – JFYE
Item
Operating Temperature Range
Rated Voltage
Withstand
Voltage
Between Terminals
Between Terminals &
Enclosure
Insulation Resistance
Capacitance
Dissipation Factor
Terminal
Strength
Pull Strength
Bending Strength
Vibration Proof
Solder Ability
Resistance
to Soldering
heat
Cold
Resistance
Dry Heat
Resistance
Appearance
Withstand Voltage
Capacitance Variation
Dissipation Factor
Insulation Resistance
Capacitance Variation
Insulation Resistance
Capacitance Variation
Appearance
Humidity
Resistance
Withstand Voltage
Insulation Resistance
Capacitance Variation
Dissipation Factor
Appearance
High
Temperature
Loading Test
Withstand Voltage
Insulation Resistance
Capacitance Variation
Dissipation Factor
Humidity
Bias Test
Appearance
Withstand Voltage
Insulation Resistance
Capacitance Variation
Performance
-40°C ~+110°C
250VAC, 275VAC, 310VAC
No abnormality.
C ≦ 0.33μF: 15,000MΩ min
C > 0.33μF: 5,000MΩ/μF min
Within specified tolerance
0.1% max at 1KHz
No cutting or slack of
terminals
No abnormality of the
appearance
At least 95% of the surface of
the lead wire dipped into is
covered with new solder.
No abnormality on
appearance
Comply with item 3
Within ±3%
Within spec of item 6 above.
Same as the spec of item 4
above
Within ±5%
C ≦ 0.33μF: 3,000MΩ min
C > 0.33μF: 1,000MΩ/μF min
Within ±5%
No abnormality on
appearance marking to be
legible
Comply with item 3
C≦0.33μF: 10,000MΩ min
C > 0.33μF: 3,000MΩ/μF min
Within ±5%
0.15% max at 1KHz (20°C)
No abnormality on
appearance marking to be
legible
Comply with item 3
C≦ 0.33μF: 10,000MΩ min
C > 0.33μF: 3,000MΩ/μF min
Within ±5%
0.15% max at 1KHz (20°C)
No abnormality on
appearance marking to be
legible
Comply with item 3
C≦ 0.33μF: 10,000MΩ min
C > 0.33μF: 3,000MΩ/μF min
Within ±10%
Test Conditions
Rated voltage x 430% (VDC)
1~5 sec charge and Discharge
current shall not exceed 10 mA
2050 VDC 1 min
Charge time: 60 ±5sec.
Charge voltage: 100VDC
Test Temp: 20°C
at 1 KHz ±10%
Measure R.V: 1 Vrms or below
Test temp: 20°C
Measure R.V: 1 Vrms or below
Test temp: 20°C
Wire diameter: 0.6&0.8 mm
Load: 1 kg, time: 10 sec.
Wire diameter: 1.0 mm
Load: 2 kg, time: 20 sec.
Wire diameter: 0.6&0.8 mm
Load: 0.5 kg, 90° x 4 time
Wire diameter: 1.0 mm
Load: 1 kg, 90° x 4 time
Frequency range 10-500-10 Hz
Amplitude: 0.75 mm,
2 hrs/direction for 3 directions
Solder temp: 245℃ ±2°C
Immersion time: 2 ±0.5sec.
Solder: SnAgCu
(Sn:96.5% Ag:3% Cu:0.5%)
Solder temp: 265 ±5°C
Immersion time: 10±0.5sec.
Temperature: -40 ±2°C
Duration: 96±4 hrs
Temperature: +110 ±2°C
Duration: 96±4 hrs
Humidity: 90~95% RH
Temperature: +40 ±2°C
Duration: 96±4 hrs
Measure after exposing at
normal state for 16 hrs.
Temperature: +110 ±2°C
Duration: 1,000 +48/-0 hrs
Applied Voltage 100% x R.V.
through series resistor of
20~1000Ω/V to the Capacitor
Measure after exposing at
normal state for 4 hrs.
Humidity: 85% RH
Temperature: 85±3℃
Duration: 1000±24hrs
Applied Voltage 240 VAC
through series resistor of
20~1000Ω/V to the Capacitor
Dissipation Factor
0.8% max at 1KHz (20°C)
Measure after exposing at
normal state for 4 hrs.
www.jbcapacitors.com www.jbcapacitors.hk
E-mail: [e-mail] Tel : [phone] Fax: [phone]