|
CPC7592_12 Datasheet, PDF (8/19 Pages) IXYS Corporation – Line Card Access Switch | |||
|
◁ |
INTEGRATED CIRCUITS DIVISION
CPC7592
1.7 Digital I/O Electrical Specifications
Parameter
Test Conditions
Symbol Minimum Typical Maximum
Unit
Input Characteristics
Input voltage, Logic low
Input voltage, Logic high
Input voltage falling
Input voltage rising
VIL
0.8
1.1
-
V
VIH
1.9
2.4
Input leakage current,
INRINGING and INTEST, VDD = 5.5 V, VBAT = -75 V, VHI = 2.4V
IIH
-
0.1
1
ïA
Logic high
Input leakage current,
INRINGING and INTEST, VDD = 5.5 V, VBAT = -75 V, VIL = 0.4V
IIL
-
0.1
1
ïA
Logic low
Input leakage current,
LATCH Logic high
VDD = 4.5 V, VBAT = -75 V, VIH = 2.4V
IIH
10
28
-
ïA
Input leakage current,
LATCH Logic low
VDD = 5.5 V, VBAT = -75 V, VIL = 0.4V
IIL
-
46
125
ïA
Input leakage current,
TSD Logic high
VDD = 5.5 V, VBAT = -75 V, VIH = 2.4
IIH
10
16
30
ïA
Input leakage current,
TSD Logic low
VDD = 5.5 V, VBAT = -75 V, VIL = 0.4V
IIL
10
16
30
ïA
Output Characteristics
Output voltage,
TSD Logic high
VDD = 5.5 V, VBAT = -75 V, ITSD = 10ïA VTSD_off
2.4
VDD
-
V
Output voltage,
TSD Logic low
VDD = 5.5 V, VBAT = -75 V, ITSD = 1mA VTSD_on
-
0
0.4
V
1.8 Voltage and Power Specifications
Parameter
Test Conditions
Symbol Minimum Typical Maximum
Unit
Voltage Requirements
VDD
-
VDD
4.5
5.0
5.5
V
VBAT1
-
VBAT
-19
-48
-72
V
1VBAT is used only for internal protection circuitry. If VBAT rises above-10 V, the device will enter the all-off state and will remain in the all-off state until the battery
drops below approximately -15 V
Power Specifications
VDD = 5 V, VBAT = -48 V, VIH = 2.4V,
Power consumption VIL = 0.4V, Measure IDD and IBAT,
Talk and All-Off States
P
-
5.5
10
mW
All other states
P
-
6.5
10
mW
VDD current in talk and
all-off states
VDD = 5 V, VBAT = -48 V, VIH = 2.4V,
IDD
VDD current in ringing VIL = 0.4V
state
IDD
-
-
1.1
2.0
mA
1.3
2.0
VBAT
current in
any
state
VDD = 5V, VBAT
VIL = 0.4V
=
-48
V,
VIH
=
2.4V,
IBAT
-
0.1
10
ïA
8
www.ixysic.com
R04
|
▷ |