IS61WV25616EDBLL Datasheet, PDF (5/14 Pages) Integrated Silicon Solution, Inc – Data control for upper and lower bytes

IS61/64WV25616EDBLL
DC ELECTRICAL CHARACTERISTICS (Over Operating Range)
Vdd = 3.3V + 10%
Symbol Parameter
Test Conditions
Min.
Max.
1 Unit
Voh
Output HIGH Voltage
Vdd = Min., Ioh = –4.0 mA
2.4
—
V
Vol
Output LOW Voltage
Vdd = Min., Iol = 8.0 mA
—
0.4
V
Vih
Input HIGH Voltage
Vil
Input LOW Voltage⁽¹⁾
2
–0.3
Vdd + 0.3
0.8
V
V
2
Ili
Input Leakage
GND ≤ Vin ≤ Vdd
–1
1
µA
Ilo
Output Leakage
GND ≤ Vout ≤ Vdd, Outputs Disabled
Note:
1. Vil (min.) = –0.3V DC; Vil (min.) = –2.0V AC (pulse width < 10 ns). Not 100% tested.
–1
1
µA
3
Vih (max.) = Vdd + 0.3V DC; Vih (max.) = Vdd + 2.0V AC (pulse width < 10 ns). Not 100% tested.
4
DC ELECTRICAL CHARACTERISTICS (Over Operating Range)
Vdd = 2.4V-3.6V
Symbol Parameter
Voh
Output HIGH Voltage
Test Conditions
Vdd = Min., Ioh = –1.0 mA
Min.
Max.
5 ^Unit
1.8
—
V
Vol
Output LOW Voltage
Vdd = Min., Iol = 1.0 mA
—
0.4
V
Vih
Input HIGH Voltage
Vil
Input LOW Voltage⁽¹⁾
2.0
–0.3
Vdd + 0.3
0.8
V
V
6
Ili
Input Leakage
GND ≤ Vin ≤ Vdd
–1
1
µA
Ilo
Note:
Output Leakage
GND ≤ Vout ≤ Vdd, Outputs Disabled
–1
1
7 ^µA
1. Vil (min.) = –0.3V DC; Vil (min.) = –2.0V AC (pulse width < 10 ns). Not 100% tested.
Vih (max.) = Vdd + 0.3V DC; Vih (max.) = Vdd + 2.0V AC (pulse width < 10 ns). Not 100% tested.
8
POWER SUPPLY CHARACTERISTICS⁽¹⁾ (Over Operating Range)
-8 -10 -20
Symbol Parameter
Test Conditions Min. Max.
Icc
Vdd Dynamic Operating Vdd = Max.,
Com. — 40
Min. Max.
— 30
Min. Max. Unit
— 25 mA
9
Supply Current
Iout = 0 mA, f = fmax Ind. — 45
— 35
— 30
Auto. — —
— 50
— 45
Icc1 Operating
Vdd = Max.,
typ.⁽²⁾
Com.
21
— 20
21
— 20
— 20 mA
10
Supply Current
Iout = 0 mA, f = 0
Ind. — 25
— 25
— 25
Auto. — —
— 40
— 40
Isb1
TTL Standby Current Vdd = Max.,
(TTL Inputs)
Vin = Vih or Vil
Com. — 10
Ind. — 15
— 10
— 15
— 10 mA
— 15
11

CE ≥ Vih, f = 0
Auto. — —
— 30
— 30
Isb2
CMOS Standby
Vdd = Max.,
Com. — 5
— 5
— 5
mA
Current (CMOS Inputs) CE ≥ Vdd – 0.2V,
Ind. — 6
— 6
— 6
12

Vin ≥ Vdd – 0.2V, or Auto. — —
— 15
— 15
Vin ≤ 0.2V, f = 0 typ.⁽²⁾
1.5
1.5
Note:
1.At f = fmax, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change.
2. Typical values are measured at Vdd = 3.0V, Ta = 25^oC and not 100% tested.
Integrated Silicon Solution, Inc. — www.issi.com
5
Rev. A
09/29/2011