VLA520-01R Datasheet, PDF (2/6 Pages) Isahaya Electronics Corporation – Hybrid IC for driving IGBT modules

MAXIMUM RATINGS (unless otherwise noted, Ta=25°C)
Symbol
Parameter
Conditions
V_CCEE
V_I
Total supply voltage
Input signal voltage
Applied between 4pin and 6pin
Applied between 13pin and 14pin
50% duty cycle, pulse width 1ms
V_O
I_OHP
I_OLP
Viso
Output voltage
Output peak current
Isolation voltage
When the output voltage is “H”
Pulse width 2µs
Sine wave voltage 60Hz, for 1minute
T_C
Case temperature
Topr Operating temperature
-
No condensation allowable
Tstg Storage temperature
No condensation allowable
Ialm Alarm output current
Applied 16pin
Valm Alarm terminal voltage
Applied between 15pin and 16pin
V_R1
Input voltage at 1pin
Applied 1pin
HYBRID IC
VLA520-01R
Hybrid IC for driving IGBT modules
Ratings
31
-1 ~ +7
V_CC
-5
5
2500
100
-20 ~ +85
-25 ~ +100
10
50
50
Unit
V
V
V
A
A
Vrms
°C
°C
°C
mA
V
V
ELECTRICAL CHARACTERISTICS (unless otherwise noted, Ta=25°C, V_CC = 15V, V_EE = -10V, RG = 3.3ohm)
Symbol
Parameter
Conditions
Limits
Min
Typ
V_CC
Supply voltage
V_EE
V_IN
Pull-up voltage on primary side
I_IH
“H” input signal current
f
Switching frequency
Recommended range
Recommended range
Recommended range
Recommended range
14.5
15
-6
-10
4.75
5
10
13
-
-
R_G
Gate resistance
Ialm Alarm output current
Recommended range
Recommended range
2
-
-
2.5
I_IH
V_OH
V_OL
t_PLH
t_r
t_PHL
t_f
t_timer
“H” input signal current
“H” output voltage
“L” output voltage
“L-H” propagation time
“L-H” rise time
“H-L” propagation time
“H-L” fall time
Timer
tdalm Alarm delay time
V_IN = 5V HC04 drive
-
-
IIH=13mA
IIH=13mA
IIH=13mA
IIH=13mA
Between start and cancel
(under input signal “OFF”)
16 pin: Pull-up 5V , Ralm = 2k ohm
Pin1: 15V and more, Pin2:open
-
13
13
14
-8
-9
0.2
0.45
-
0.3
0.2
0.4
-
0.3
1
1.4
-
6.5
Max ^Unit
17.5
V
-12
V
5.25
V
16
mA
30 kHZ
-
ohm
5
mA
-
mA
-
V
-
V
0.8
µs
1
µs
0.7
µs
1
µs
2
ms
10
µs
t_trip1
Controlled time detect short circuit 1
Pin1: 15V and more, Pin2:open
-
2.7
-
µs
t_trip2
Controlled time detect short circuit 2 (*2)
Pin1: 15V and more, Pin2-4:10pF
(connective capacitance)
-
3.1
-
µs
V_SCth SC detect threshold voltage
Measurement point is 1pin.
VCC
-8
VCC
-7.4
VCC
-6.7
V
(*2) Length of wiring of condenser controlled time detect short-circuit is within 5cm from pin2 and pin4 coming and going.
2