IR2131_15 Datasheet, PDF (2/10 Pages) International Rectifier – 3 HIGH SIDE AND 3 LOW SIDE DRIVER

IR2131^{(J)(S) & (PbF)}
Absolute Maximum Ratings
Absolute Maximum Ratings indicate sustained limits beyond which damage to the device may occur. All voltage param-
eters are absolute voltages referenced to COM. The Thermal Resistance and Power Dissipation ratings are measured under
board mounted and still air conditions. Additional Information is shown in Figures 7 through 10.
Symbol
Definition
Min.
Max. Units
V_B1,2,3
V_S1,2,3
V_HO1,2,3
V_CC
V_SS
V_LO1,2,3
V_IN
V_FLT
dV_S/dt
P_D
Rth_JA
T_J
T_S
T_L
High Side Floating Supply Voltage
High Side Floating Offset Voltage
High Side Floating Output Voltage
Low Side and Logic Fixed Supply Voltage
Logic Ground
Low Side Output Voltage
Logic Input Voltage (HIN1,2,3 ,LIN1,2,3 ,FLT - CLR ,SD &ITRIP)
FAULT Output Voltage
Allowable Offset Supply Voltage Transient
Package Power Dissipation @ T_A ≤ +25°C
Thermal Resistance, Junction to Ambient
Junction Temperature
Storage Temperature
Lead Temperature (Soldering, 10 seconds)
(28 Lead DIP)
(28 Lead SOIC)
(44 Lead PLCC)
(28 Lead DIP)
(28 Lead SOIC)
(44 Lead PLCC)
-0.3
V_B1,2,3 - 25
V_S1,2,3 - 0.3
-0.3
V_CC - 25
-0.3
V_SS - 0.3
V_SS - 0.3
—
—
—
—
—
—
—
—
-55
—
625
V_B1,2,3 + 0.3
V_B1,2,3 + 0.3
25
V_CC + 0.3
V_CC + 0.3
(V_SS + 15) or
(V_CC + 0.3)
whichever
is lower
V_CC + 0.3
50
1.5
1.6
2.0
83
78
63
150
150
300
V
V/ns
W
°C/W
°C
Recommended Operating Conditions
The Input/Output logic timing diagram is shown in Figure 1. For proper operation the device should be used within the
recommended conditions. All voltage parameters are absolute voltages referenced to COM. The V_S offset rating is tested
with all supplies biased at 15V differential.
Symbol
V_B1,2,3
V_S1,2,3
V_HO1,2,3
V_CC
V_SS
V_LO1,2,3
V_IN
V_FLT
T_A
Definition
High Side Floating Supply Voltage
High Side Floating Offset Voltage
High Side Floating Output Voltage
Low Side and Logic Fixed Supply Voltage
Logic Ground
Low Side Output Voltage
Logic Input Voltage (HIN1,2,3 , LIN1,2,3 ,FLT - CLR , SD & ITRIP)
FAULT Output Voltage
Ambient Temperature
Min.
V_S1,2,3 + 10
Note 1
V_S1,2,3
10
-5
0
V_SS
V_SS
-40
Max.
V_S1,2,3 + 20
600
V_B1,2,3
20
5
V_CC
V_SS + 5
V_CC
125
Units
V
°C
Note 1: Logic operational for V_S of -5V to +600V. Logic state held for V_S of -5V to -V_BS. (Please refer to the Design Tip
DT97-3 for more details).
Note 2: All input pins, CA- and CAO pins are internally clamped with a 5.2V zener diode.
2
www.irf.com