90MT Datasheet, PDF (2/7 Pages) International Rectifier – THREE PHASE BRIDGE

90-110MT..KB Series
Bulletin I27501 rev. A 05/03
ELECTRICAL SPECIFICATIONS
Voltage Ratings
Voltage
Type number Code
V_RRM , maximum repetitive
peak reverse voltage
V
80
800
100
1000
90-110MT..KB
120
140
160
1200
1400
1600
V_RSM , maximum non-
repetitive peak rev. voltage
V
900
1100
1300
1500
1700
I_RRM max.
@ T_J max.
mA
10
Forward Conduction
Parameter
90MT.KB 110MT.KB Units Conditions
I_O Maximum DC output current
@ Case temperature
I_FSM Maximum peak, one-cycle forward,
non-repetitive surge current
I²t Maximum I²t for fusing
I²âˆšt Maximum I²âˆšt for fusing
V_F(TO)1 Low level value of threshold voltage
V_F(TO)2 High level value of threshold voltage
r_f1 Low level value of forward slope resistance
r_f2 High level value of forward slope resistance
V_FM Maximum forward voltage drop
V_INS RMS isolation voltage
90 (120)
90 (61)
770
810
650
680
3000
2700
2100
1900
30000
0.89
1.05
5.11
4.64
1.6
4000
110 (150)
90 (57)
950
1000
800
840
4500
4100
3200
2900
45000
0.81
0.99
4.37
4.64
1.4
4000
A 120° Rect conduction angle
°C
A t = 10ms No voltage
t = 8.3ms reapplied
t = 10ms 100% V_RRM
t = 8.3ms reapplied Initial T_J = T_J max.
A²s t = 10ms No voltage
t = 8.3ms reapplied
t = 10ms 100% V_RRM
t = 8.3ms reapplied
A²âˆšs t = 0.1 to 10ms, no voltage reapplied
V (16.7% x π x I_F(AV) < I < π x I_F(AV)), @ T_J max.
(I > π x I_F(AV)), @ T_J max.
mΩ (16.7% x π x I_F(AV) < I < π x I_F(AV)), @ T_J max.
(I > π x I_F(AV)), @ T_J max.
V I_pk = 150A, T_J = 25°C, t_p = 400µs single junction
V T_J = 25°C, all terminal shorted
f = 50Hz, t = 1s
Thermal and Mechanical Specifications
Parameter
90MT.KB 110MT.KB Units Conditions
T_J Max. junction operating temperature range
T_stg Max. storage temperature range
R_thJC Max. thermal resistance, junction to case
R_thCS Max. thermal resistance, case to heatsink
T Mounting torque ± 10% to heatsink
to terminal
wt Approximate weight
-40 to 150
-40 to 150
0.21
0.18
1.26
1.07
0.25
0.21
1.47
1.25
0.03
4 to 6
3 to 4
176
°C
°C
K/W DC operation per module
DC operation per junction
120° Rect condunction angle per module
120° Rect condunction angle per junction
K/W Per module
Mounting surface smooth, flat and greased
Nm ^{A mounting compound is recommended and the}
torque should be rechecked after a period of 3
hours to allow for the spread of the compound.
Lubricated threads.
g
2
www.irf.com