IR2136 Datasheet, PDF (1/36 Pages) International Rectifier – 3-PHASE BRIDGE DRIVER

Data Sheet No. PD60166 revS
IR2136/IR21362/IR21363/IR21365/
IR21366/IR21367/IR21368 ^(J&S) & (PbF)
Features
3-PHASE BRIDGE DRIVER
• Floating channel designed for bootstrap operation
Fully operational to +600V
Packages
Tolerant to negative transient voltage - dV/dt immune
• Gate drive supply range from 10 to 20V (IR2136/IR21368),
11.5 to 20V (IR21362) or 12 to 20V (IR21363/IR21365/
IR21366/IR21367)
• Undervoltage lockout for all channels
• Over-current shutdown turns off all six drivers
• Independent 3 half-bridge drivers
• Matched propagation delay for all channels
• Cross-conduction prevention logic
• Lowside outputs out of phase with inputs. High side
28-Lead SOIC
28-Lead PDIP
44-Lead PLCC w/o 12 leads
outputs out of phase (IR2136/IR21363/IR21365/
IR21366/IR21367/IR21368) or in phase
Feature Comparison: IR2136/IR21362/IR21363/
(IR21362) with inputs.
IR21365/IR21366/IR21367/IR21368
• 3.3V logic compatible
• Lower di/dt gate driver for
Part
IR2136 IR21362 IR21363 IR21365 IR21366 IR21367 IR21368
Input Logic HIN, LIN HIN/LIN HIN, LIN HIN, LIN HIN, LIN HIN, LIN HIN,LIN
better noise immunity
• Externally programmable
Ton (typ.) 400ns
Toff (typ.) 380ns
400ns
380ns
400ns
380ns
400ns 250ns
380ns 180ns
250ns
180ns
400ns
380ns
delay for automatic fault
V_IH (typ.) 2.7V
2.7V
2.7V
2.7V
clear
VIL (typ.) 1.7V
1.7V
1.7V
1.7V
• Also available LEAD-FREE Vitrip+
0.46V 0.46V 0.46V 4.3V
2.0V
1.3V
0.46V
2.0V
1.3V
4.3V
2.0V
1.3V
4.3V
UV CC/BS+ 8.9V
10.4V 11.2V 11.2V 11.2V 11.2V 8.9V
Description
UV CC/BS- 8.2V
9.4V
11.0V 11.0V 11.0V 11.0V 8.2V
The IR2136/IR21362/IR21363/IR21365/IR21366/IR21367/IR21368(J&S) are high votage, high speed power MOSFET
and IGBT drivers with three independent high and low side referenced output channels for 3-phase applications.
Proprietary HVIC technology enables ruggedized monolithic construction. Logic inputs are compatible with CMOS
or LSTTL outputs, down to 3.3V logic. A current trip function which terminates all six outputs can be derived from
an external current sense resistor. An enable function is available to terminate all six outputs simultaneously. An
open-drain FAULT signal is provided to indicate that an overcurrent or undervoltage shutdown has occurred.
Overcurrent fault conditions are cleared automatically after a delay programmed externally via an RC network
connected to the RCIN input. The output drivers feature a high pulse current buffer stage designed for minimum
driver cross-conduction. Propagation delays are matched to simplify use in high frequency applications. The
floating channel can be used to drive N-channel power MOSFETs or IGBTs in the high side configuration which
operates up to 600 volts.
Typical Connection
VCC
HIN1,2,3 / HIN1,2,3
LIN1,2,3
(Refer to Lead Assign-
ments for correct pin con-
FAULT
EN
figuration). This/These
diagram(s) show electri-
cal connections only.
Please refer to our Appli-
cation Notes and
DesignTips for proper cir-
cuit board layout.
GND
VCC
HIN1,2,3 / HIN1,2,3
LIN1,2,3
FAULT
EN
RCIN
ITRIP
VSS
VB1,2,3
HO1,2,3
VS1,2,3
LO1,2,3
COM
up to 600V
TO
LOAD
IR2136(2)(3)(5)(6)(7)(8)
www.irf.com
1