B100 Datasheet, PDF (2/2 Pages) Intronics Power, Inc. – 1WATT DC-DC CONVERTERS

FILE NAME: B100 RevB.DOC, REVISION: January 19, 2007 V15
SPECIFICATIONS
All Specifications Typical At Nominal Line, Full Load, and 25℃ Unless Otherwise Noted
INPUT SPECIFICATIONS :
GENERAL SPECIFICATIONS :
Input Voltage Range....……………................................................10%
Efficiency...........................................………..…………............See Table
Isolation Voltage...................................……..……….........1000 VDC min.
Input Filter ……………………………………………..………Capacitive
Isolation Resistance .....................…….………….………10^9 Ohms min.
Switching Frequency .............................……......................100KHz typ.
OUTPUT SPECIFICATIONS :
Operating Ambient Temperature Range...………...…….... -40℃ to +85℃
Voltage Accuracy…………………....……………….........…±3.0% max.
De-rating, Above 85℃ …………..……… Linearly to Zero power at 100℃
Ripple and Noise, 20MHz BW....SIP Models......……..75mV p-p max.
SMD Models……....120mV p-p max.
Temperature Coefficient....................….………….......±0.05%/C max.
Short Circuit Protection...................….…………Momentary 1sec. max.
Line Regulation, Note1..….………...…………………….....±1.2% max.
Load Regulation, Note2…………………..........…………....±10% max.
Case temperature (Note5)………..………….………..…..…...+100℃ max.
Cooling………………………………………..….………..Natural Convection
Storage Temperature Range ...…............………....…....... -55℃ to +125℃
Dimensions:
SIP Models………….0.77 x 0.24 x 0.40inches(19.5 x 6.1 x 10.2mm)
SMD Models(Single)…..0.5 x 0.31 x 0.27inches(12.7 x 8.0 x 6.8mm)
SMD Models(Dual)…. 0.6 x 0.31 x 0.27inches(15.24 x 8.0 x 6.8mm)
Case Material………..SIP Models………Non-conductive black plastic
SMD Models………….Epoxy molding compound
Weight………..……………………………………………………………..1.8g
NOTE :
1. Line regulation is per 1.0% change in input voltage
2. Load regulation is for load change from 100% to 20%
3. The output noise is measured with 0.33uF ceramic capacitor.
4. Suffix “S” to the model number with SMD packages
5. Maximum case temperature under any operating condition should
not be exceeded 100℃.
Dimensions:
Al l Di mensi ons I n I nches( mm)
Tol er ance I nches
Mi l l i met er s
X. XX±0. 01 X. X±0. 25
X. XXX±0. 005 X. XX±0. 13
Pi n
±0. 002
±0. 05
SI P PACKAGES
SMD PACKAGES
Typical Derating curve for Natural Convection
120%
100%
80%
60%
40%
20%
Natural
Convection
0%
-40 -20
0
20 40 60
Ambient Temperature(^oC)
80 100
PIN CONNECTION
Pin Single Output Dual Output
1 +Vin
+Vin
2 -Vin
4 -Vout
5 No Pin
6 +Vout
-Vin
-Vout
Common
+Vout
NA:Not Available for Electrical Connection
PIN CONNECTION
Pin
Single Output
1
-Vin
2
+Vin
3
No Pin
4
-Vout
5
+Vout
6
No Pin
7
No Pin
8
NA
-2-
PIN CONNECTION
Pin
Dual Output
1
-Vin
2
+Vin
3
No Pin
4
Common
5
-Vout
6
NA
7
+Vout
8
No Pin
9
No Pin
10
NA