X28HC64_09 Datasheet, PDF (9/17 Pages) Intersil Corporation – 5 Volt, Byte Alterable EEPROM

X28HC64
Absolute Maximum Ratings
Temperature Under Bias
X28HC64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-10°C to +85°C
X28HC64I. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage on any Pin with Respect to V_ss . . . . . . . . . . . . . . -1V to +7V
DC Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
Thermal Information
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
*Pb-free PDIPs can be used for through hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
Recommended Operating Conditions
Commercial Temperature Range. . . . . . . . . . . . . . . . . 0°C to +70°C
Industrial Temperature Range . . . . . . . . . . . . . . . . . .-40°C to +85°C
Supply Voltage Range
X28HC64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5V ±10%
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
DC Electrical Specifications
Over recommended operating conditions, unless otherwise specified. Parameters with MIN and/or MAX
limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by
characterization and are not production tested.
PARAMETER
SYMBOL
TEST CONDITIONS
TYP
MIN (Note 3) MAX UNIT
V_CC Current (active) (TTL Inputs)
I_CC CE = OE = V_IL, WE = V_IH, All I/O’s = open, address
inputs = TTL levels @ f = 10 MHz
15
40 mA
V_CC Current (Standby) (TTL Inputs)
I_SB1 CE = V_IH, OE = V_IL All I/O’s = open, other inputs = V_IH
V_CC Current (Standby) (CMOS Inputs)
I_SB2 CE = V_CC - 0.3V, OE = GND, All I/O’s = open, other
inputs = V_CC - 0.3V
Input Leakage Current
I_LI
V_IN = V_SS to V_CC
Output Leakage Current
I_LO
V_OUT = V_SS to V_CC, CE = V_IH
Input LOW Voltage (Note 4)
V_lL
Input HIGH Voltage (Note 4)
V_IH
Output LOW Voltage
V_OL I_OL = 5mA
Output HIGH Voltage
V_OH I_OH = -5mA
NOTES:
3. Typical values are for T_A = +25°C and nominal supply voltage
4. V_IL min. and V_IH max. are for reference only and are not tested.
1
2
mA
100
200 µA
±10 µA
±10 µA
-1
0.8
V
2
V_CC + 1 V
0.4
V
2.4
V
Endurance and Data Retention
PARAMETER
Minimum Endurance
Data Retention
Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified.
Temperature limits established by characterization and are not production tested.
MIN
MAX
UNIT
100,000
Cycles
100
Years
9
FN8109.2
August 28, 2009