X9317 Datasheet, PDF (6/15 Pages) Intersil Corporation – Low Noise, Low Power, 100 Taps

X9317
Absolute Maximum Ratings
Junction Temperature Under Bias . . . . . . . . . . . . . .-65°C to +135°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage on CS, INC, U/D and V_CC
with Respect to V_SS . . . . . . . . . . . . . . . . . . . . . . . . . . . -1V to +7V
R_H, R_W, R_L to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+6V
Lead Temperature (soldering 10s). . . . . . . . . . . . . . . . . . . . . . 300°C
I_W (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±8.8mA
CAUTION: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation
of the device (at these or any other conditions above those listed in the operational sections of this specification) is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
Potentiometer Specifications V_CC = Full Range, T_A = Full Operating Temperature Range unless otherwise stated
SYMBOL
PARAMETER
TEST CONDITIONS/NOTES
TYP
MIN (Note 4)
R_TOTAL
V_RH/_RL
End to end resistance tolerance
R_H/R_L terminal voltage
Power rating
R_W
Wiper resistance
I_W
Wiper current (Note 5)
Noise (Note 7)
See ordering information for values
V_SS = 0V
R_TOTAL ≥ 10kΩ
R_TOTAL = 1kΩ
I_W = 1mA, V_CC = 5V
I_W = 1mA, V_CC = 2.7V
See test circuit
Ref: 1kHz
-20
V_SS
200
400
-4.4
-120
Resolution
1
Absolute linearity (Note 1)
V(RH) = V_CC,
-1
V(RL) = 0V
Relative linearity (Note 2)
-0.2
MAX
+20
V_CC
10
25
400
1000
+4.4
+1
+0.2
C_H/C_L/C_W
(Note 5)
V_CC
R_TOTAL temperature coefficient (Note 5)
Ratiometric temperature coefficient
(Notes 5, 6)
Potentiometer capacitances
Supply Voltage
See equivalent circuit
X9317
X9317-2.7
±300
-20
+20
10/10/25
4.5
5.5
2.7
5.5
UNIT
%
V
mW
mW
Ω
Ω
mA
dBV
%
MI
(Note 3)
MI
(Note 3)
ppm/°C
ppm/°C
pF
V
V
DC Electrical Specifications V_CC = 5V ±10%, T_A = Full Operating Temperature Range unless otherwise stated
SYMBOL
PARAMETER
TEST CONDITIONS
TYP
MIN (Note 4)
MAX
I_CC1
VCC active current (Increment)
I_CC2
I_SB
I_LI
V_IH
VCC active current (Store)
(non-volatile write)
Standby supply current
CS, INC, U/D input leakage current
CS, INC, U/D input HIGH voltage
CS = V_IL, U/D = V_IL or V_IH and INC =
V_IL/V_IH @ min. t_CYC
R_L, R_H, R_W not connected
CS = V_IH, U/D = V_IL or V_IH and INC = V_IL
or V_IH. R_L, R_H, R_W not connected
CS ≥ V_IH, U/D and INC = V_IL
R_L, R_H, R_W not connected
V_IN = V_SS to V_CC
-10
V_CC x
0.7
50
400
1
+10
V_CC +
0.5
V_IL
CS, INC, U/D input LOW voltage
-0.5
V_CC x
0.1
UNIT
µA
µA
µA
µA
V
V
6
FN8183.1
September 9, 2005