ISL37300P-EVAL Datasheet, PDF (6/6 Pages) Intersil Corporation – PRISM 2.5 11Mbps Wireless Local Area Network PC Card

ISL37300P-EVAL
Electrical Specifications Test Conditions: Supply Voltage (V_CC) = 3.3V, Ambient Temperature (T_A) = 25^oC,
Unless Otherwise Specified (Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Receive Sensitivity
RX_S
1Mbps, 8% PER
-93
dBm
2Mbps, 8% PER
-90
dBm
5.5Mbps, 8% PER
-89
dBm
11Mbps, 8% PER
-85
dBm
Multipath Delay Spread
using Naftali Model
(T_Delay)
2Mbps, 8% PER
5.5Mbps, 8% PER
>290
ns
200
ns
11Mbps, 8% PER
110
ns
Multipath Receive Sensitivity
using JTC models (note 5)
RX_S_JTC
1Mbps, 8% PER, Office C
Delay spread = 450ns
-83
dBm
2Mbps, 8% PER, Commercial B
-81
Delay spread = 150ns
dBm
5.5Mbps, 8% PER, Commercial B
-80
Delay spread = 150ns
dBm
11Mbps, 8% PER, Commercial B
-73
Delay spread = 150ns
dBm
Maximum Receive Level
RX_MAX PER <8% (11 Mbps)
>10
dBm
Third Order Intercept Point (Input)
IIP3_HG High gain mode
-9.5
dBm
IIP3_LG Low gain mode
TBD
dBm
Carrier Suppression
TX_sup Test Mode
-45
-40
-34
dB
Image Rejection
IR
PER <8%
45
dB
IF Rejection
IFR
PER <8%
>84
dB
Adjacent Channel Rejection
ACR
PER <8%, 11Mbps signal w/ 11
52.5
53
53.9
dB
Mbps jammer 25 MHz offset (Note
6)
Data Rate (Physical Layer)
Rate
1, 2, 5.5
and 11
Mbps
5. For more information on JTC models, refer to Application Note AN9895 [7].
6. The adjacent channel measurement is carried out on two channels separated by 25MHz (five channels). The jammer signal is a continuos
DSSS 11 Mbps waveform with -40dBc first sidelobes.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
Sales Office Headquarters
NORTH AMERICA
Intersil Corporation
7585 Irvine Center Drive
Suite 100
Irvine, CA 92618
TEL: [phone]
FAX: [phone]
Intersil Corporation
2401 Palm Bay Rd.
Palm Bay, FL 32905
TEL: [phone]
FAX: [phone]
EUROPE
Intersil Europe Sarl
Ave. William Graisse, 3
1006 Lausanne
Switzerland
TEL: [phone]
FAX: [phone]
ASIA
Intersil Corporation
Unit 1804 18/F Guangdong Water Building
83 Austin Road
TST, Kowloon Hong Kong
TEL: [phone]
FAX: [phone]
6