English
Language : 

ISL58831 Datasheet, PDF (5/12 Pages) Intersil Corporation – Dual Laser Driver with APC Amplifier and Spread Spectrum Oscillator
ISL58831
Absolute Maximum Ratings (TA = +25°C)
Voltages Applied to:
VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +6.0V
WEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VDD +0.5V
IINx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +5.0V
IOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VDD+0.5V
Power Dissipation (maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . See page 9
IOUT Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . 300mA average, 500mAP-P
Thermal Information
Thermal Resistance (Typical)
JA (°C/W)
24 Ld QFN Package (Note 4). . . . . . . . . . . . . . . . . . . . . .
42
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .+150°C
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see TB493
Recommended Operating Conditions
Operating Ambient Temperature Range . . . . . . . . . . . . . . . . 0°C to +80°C
VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V ±10%
RFREQ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500Ω (minimum)
RAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500Ω (minimum)
FOSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100MHz to 600MHz
AOSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mAP-P to 100mAP-P
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and
operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
4. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
NOTE: Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
Electrical Specifications VDD = 5V, TA = +25°C, ENABLE = HI, WEN = HI, OSCEN = LO, SEL1 = HI, unless otherwise specified.
PARAMETER
DESCRIPTION
TEST CONDITIONS
MIN
TYP
MAX UNIT
VDD
Supply Voltage
IS1
Supply Current (Disabled)
ENABLE = <0.5V
4.5
5.0
5.5
V
0.1
100
µA
IS2
IS3
IS4
IS5
DVLO
EVLO
DVHI
EVHI
DVHICD
DVLOCD
DILO
DIHI
VSHUT
Supply Current
Supply Current
Supply Current
Supply Current
Digital Low Voltage
Enable Low Voltage
Digital High Voltage
Enable High Voltage
Digital High Voltage
Digital Low Voltage
Digital Low Current
Digital High Current
VDD Shutdown Voltage
IINR = 0µA, IIN2/3/4 = 20µA
OSCEN = HI, IINR = 0µA, IIN2/3/4 = 20µA
IINR = 0µA, IIN2/3/4 = 500µA
IINR = 200µA, IIN2/3/4 = 500µA
WEN2/3/4, OSCEN inputs
ENABLE pin (to guarantee IS1)
WEN2/3/4, OSCEN inputs
ENABLE pin only
SEL1 only
SEL1 only
SEL1, OSCEN, ENABLE, WEN = 0.0V
SEL1, OSCEN, ENABLE, WEN = 5.0V
34
40
46
mA
50
60
70
mA
61
73
85
mA
94
112 130
mA
1.3
V
0.5
V
2.2
V
2.2
V
2.2
V
1.3
V
-100
µA
100
µA
3.5
3.9
V
Laser Amplifier VDD = 5V, TA = +25°C, ENABLE = HI unless otherwise specified.
PARAMETER
DESCRIPTION
CONDITIONS
GAINR
GAINR2
GAIN2
GAIN3
GAIN4
IOUTR
Best Fit Current Gain
Best Fit Current Gain
Best Fit Current Gain
Best Fit Current Gain
Best Fit Current Gain
Output Current
Channel R - IOUT1 (Note 5)
Channel R2 - IOUT2 (Note 5)
Channel 2 - IOUT1 (Note 5)
Channel 3 - IOUT1 (Note 5)
Channel 4 - IOUT1 (Note 5)
VDD = 4.5V, VOUT = 3.4V, output is sourcing,
channel R - IOUT1 (Note 5), IINR = 2mA
MIN
TYP
MAX UNIT
140 165 190 mA/mA
70
82
95 mA/mA
210 250 290 mA/mA
170 200 230 mA/mA
80
100 120 mA/mA
150
mA
Submit Document Feedback
5
FN7440.1
January 28, 2016