English
Language : 

ISL43140_15 Datasheet, PDF (5/17 Pages) Intersil Corporation – Low-Voltage, Single and Dual Supply,High Performance, Quad SPST, Analog Switches
◁
ISL43140, ISL43141, ISL43142
Electrical Specifications: ±5V Supply Test Conditions VSUPPLY = 4.5V to 5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 6),
Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
OFF Isolation
Crosstalk, Note 10
RL = 50, CL = 15pF, f = 100kHz,
VNO or VNC = 1VRMS, See Figures 4, 6, and 19
All Hostile Crosstalk
RL = 50, CL = 15pF, f = 10MHz,
VNO or VNC = 1VRMS, See Figure 19
Power Supply Rejection Ratio
RL = 50, CL = 15pF, f = 1MHz, See Figure 20
POWER SUPPLY CHARACTERISTICS
TEMP
(°C)
25
25
25
(NOTE 7)
MIN
-
-
-
TYP
>90
<-90
-60
(NOTE 7)
MAX UNITS
-
dB
-
dB
-
dB
25
-
60
-
dB
Power Supply Range
Full
2
-
6
V
Positive Supply Current, I+
VS = 5.5V, VIN = 0V or V+, Switch On or Off
25
-1
0.05
1
A
Full
-1
-
1
A
Negative Supply Current, I-
25
-1
0.05
1
A
Full
-1
-
1
A
NOTES:
6. VIN = Input voltage to perform proper function.
7. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
8. Leakage parameter is 100% tested at high temp, and guaranteed by correlation at 25°C.
9. Flatness is defined as the delta between the maximum and minimum RON values over the specified voltage range.
10. Between any two switches.
Electrical Specifications: 12V Supply Test Conditions: V+ = +10.8V to +13.2V, V- = GND = 0V, VINH = 5V, VINL = 0.8V (Note 6),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
ON Resistance, RON
V+ = 10.8V, ICOM = 1.0mA, VNO or VNC = 9V,
See Figure 5
RON Matching Between Channels,
RON
RON Flatness, RFLAT(ON)
V+ = 10.8V, ICOM = 1.0mA, VNO or VNC = 9V
V+ = 10.8V, ICOM = 1.0mA, VNO or VNC = 3V, 6V, 9V,
Note 9
NO or NC OFF Leakage Current,
INO(OFF) or INC(OFF)
V+ = 13.2V, VCOM = 1V, 10V, VNO or VNC = 10V, 1V,
Note 8
COM OFF Leakage Current,
ICOM(OFF)
V+ = 13.2V, VCOM = 10V, 1V, VNO or VNC = 1V, 10V,
Note 8
COM ON Leakage Current,
ICOM(ON)
V = 13.2V, VCOM = 1V, 10V, or VNO or VNC = 1V,
10V, Note 8
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, VINH
Input Voltage Low, VINL
Input Current, IINH, IINL
DYNAMIC CHARACTERISTICS
V+ = 13.2V, VIN = 0V or V+
Turn-ON Time, tON
V+ = 10.8V, VNO or VNC = 10V, RL = 300, CL = 35pF,
VIN = 0 to 3.3V, See Figure 1
Turn-OFF Time, tOFF
V+ = 10.8V, VNO or VNC = 10V, RL = 300, CL = 35pF,
VIN = 0 to 3.3V, See Figure 1
Break-Before-Make Time Delay
(ISL43142), tD
V+ = 13.2V, VNO or VNC = 10V, RL = 300, CL = 35pF,
VIN = 0 to 3.3V, See Figure 3
TEMP
(°C)
Full
25
Full
25
Full
25
Full
25
Full
25
Full
25
Full
Full
Full
Full
25
Full
25
Full
Full
(NOTE 7)
MIN
0
-
-
-
-
-
-
-1
-5
-1
-5
-2
-10
3.5
-
-1
-
-
-
-
0
(NOTE 7)
TYP
MAX UNITS
-
V+
V
50
65

60
75

2
2.5

-
5

8
12

9
13

-
1
nA
-
5
nA
-
1
nA
-
5
nA
-
2
nA
-
10
nA
3.1
-
V
-
0.8
V
-
1
A
30
70
ns
34
100
ns
18
50
ns
20
75
ns
8
-
ns
5
 ▷