ISL43140_04 Datasheet, PDF (5/16 Pages) Intersil Corporation – Low-Voltage, Single and Dual Supply, High Performance, Quad SPST, Analog Switches

ISL43140, ISL43141, ISL43142
Electrical Specifications: ±5V Supply Test Conditions V_SUPPLY = ±4.5V to ±5.5V, GND = 0V, V_INH = 2.4V, V_INL = 0.8V (Note 6),
Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
TEMP (NOTE 7)
(NOTE 7)
(°C)
MIN
TYP
MAX UNITS
OFF Isolation
Crosstalk, Note 10
R_L = 50Ω, C_L = 15pF, f = 100kHz,
V_NO or V_NC = 1V_RMS, See Figures 4, 6, and 19
25
-
>90
-
dB
25
-
<-90
-
dB
All Hostile Crosstalk
R_L = 50Ω, C_L = 15pF, f = 10MHz,
V_NO or V_NC = 1V_RMS, See Figure 19
Power Supply Rejection Ratio
R_L = 50Ω, C_L = 15pF, f = 1MHz, See Figure 20
POWER SUPPLY CHARACTERISTICS
25
-
-60
-
dB
25
-
60
-
dB
Power Supply Range
Full
±2
-
±6
V
Positive Supply Current, I+
V_S = ±5.5V, V_IN = 0V or V+, Switch On or Off
25
-1
0.05
1
µA
Full
-1
-
1
µA
Negative Supply Current, I-
25
-1
0.05
1
µA
Full
-1
-
1
µA
NOTES:
6. V_IN = Input voltage to perform proper function.
7. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
8. Leakage parameter is 100% tested at high temp, and guaranteed by correlation at 25°C.
9. Flatness is defined as the delta between the maximum and minimum R_ON values over the specified voltage range.
10. Between any two switches.
Electrical Specifications: 12V Supply Test Conditions: V+ = +10.8V to +13.2V, V- = GND = 0V, V_INH = 5V, V_INL = 0.8V (Note 6),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 7)
(°C)
MIN
(NOTE 7)
TYP
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
ON Resistance, R_ON
V+ = 10.8V, I_COM = 1.0mA, V_NO or V_NC = 9V,
See Figure 5
Full
0
25
-
Full
-
R_ON Matching Between Channels, V+ = 10.8V, I_COM = 1.0mA, V_NO or V_NC = 9V
∆R_ON
25
-
Full
-
R_ON Flatness, R_FLAT(ON)
V+ = 10.8V, I_COM = 1.0mA, V_NO or V_NC = 3V, 6V, 9V, 25
-
Note 9
Full
-
-
V+
V
50
65
Ω
60
75
Ω
2
2.5
Ω
-
5
Ω
8
12
Ω
9
13
Ω
NO or NC OFF Leakage Current, V+ = 13.2V, V_COM = 1V, 10V, V_NO or V_NC = 10V, 1V,
25
-1
-
1
nA
I_NO(OFF) or I_NC(OFF)
Note 8
Full
-5
-
5
nA
COM OFF Leakage Current,
V+ = 13.2V, V_COM = 10V, 1V, V_NO or V_NC = 1V, 10V,
25
-1
-
1
nA
I_COM(OFF)
Note 8
Full
-5
-
5
nA
COM ON Leakage Current,
I_COM(ON)
V+ = 13.2V, V_COM = 1V, 10V, or V_NO or V_NC = 1V,
25
-2
-
10V, Note 8
Full
-10
-
2
nA
10
nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, V_INH
Input Voltage Low, V_INL
Input Current, I_INH, I_INL
DYNAMIC CHARACTERISTICS
V+ = 13.2V, V_IN = 0V or V+
Full
3.5
3.1
-
V
Full
-
-
0.8
V
Full
-1
-
1
µA
Turn-ON Time, t_ON
V+ = 10.8V, V_NO or V_NC = 10V, R_L = 300Ω, C_L = 35pF, 25
-
V_IN = 0 to 3.3V, See Figure 1
Full
-
30
70
ns
34
100
ns
Turn-OFF Time, t_OFF
V+ = 10.8V, V_NO or V_NC = 10V, R_L = 300Ω, C_L = 35pF, 25
-
V_IN = 0 to 3.3V, See Figure 1
Full
-
18
50
ns
20
75
ns
Break-Before-Make Time Delay
V+ = 13.2V, V_NO or V_NC = 10V, R_L = 300Ω, C_L = 35pF, Full
0
8
-
ns
(ISL43142), t_D
V_IN = 0 to 3.3V, See Figure 3
5