ISL3150E_08 Datasheet, PDF (5/20 Pages) Intersil Corporation – ±16.5kV ESD (IEC61000-4-2) Protected, Large Output Swing, 5V, Full Fail-Safe, 1/8 Unit Load, RS-485/RS-422 Transceivers

ISL3150E, ISL3152E, ISL3153E, ISL3155E, ISL3156E, ISL3158E
Absolute Maximum Ratings
V_CC to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Input Voltages
DI, DE, RE . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to (V_CC + 0.3V)
Input/Output Voltages
A/Y, B/Z, A, B, Y, Z . . . . . . . . . . . . . . . . . . . . . . . . . . . -9V to +13V
A/Y, B/Z, A, B, Y, Z (Transient Pulse Through 100Ω) . . . . . . ±25V
RO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to (V_CC +0.3V)
Short Circuit Duration
Y, Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . See Specification Table
Thermal Information
Thermal Resistance (Typical, Note 1)
θ_JA (°C/W)
8 Ld SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
105
8 Ld MSOP, PDIP* . . . . . . . . . . . . . . . . . . . . . . . . . .
140
10 Ld MSOP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
130
14 Ld SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
130
Maximum Junction Temperature (Plastic Package) . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
*Pb-free PDIPs can be used for through hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTE:
1. θ_JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications Test Conditions: V_CC = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at V_CC = 5V, T_A = +25°C
(Note 2).
PARAMETER
SYMBOL
TEST CONDITIONS
TEMP MIN
MAX
(°C) (Note 10) TYP (Note 10) UNITS
DC CHARACTERISTICS
Driver Differential V_OUT (No load)
V_OD1
Full
-
-
V_CC
V
Driver Differential V_OUT (Loaded)
V_OD2 R_L = 100Ω (RS-422) (Figure 1A)
Full
2.8
3.6
-
V
R_L = 54Ω (RS-485) (Figure 1A)
Full
2.4
3.1
V_CC
V
R_L = 15Ω (Eight 120Ω terminations) (Note 11) 25
-
1.65
-
V
R_L = 60Ω, -7V ≤ V_CM ≤ 12V (Figure 1B)
Full
2.4
3
-
V
Change in Magnitude of Driver
Differential V_OUT for
Complementary Output States
ΔV_OD R_L = 54Ω or 100Ω (Figure 1A)
Full
-
0.01
0.2
V
Driver Common-Mode V_OUT
Change in Magnitude of Driver
Common-Mode V_OUT for
Complementary Output States
V_OC
ΔV_OC
R_L = 54Ω or 100Ω (Figure 1A)
R_L = 54Ω or 100Ω (Figure 1A)
Full
-
-
3.15
V
Full
-
0.01
0.2
V
Logic Input High Voltage
Logic Input Low Voltage
DI Input Hysteresis Voltage
Logic Input Current
Input Current (A, B, A/Y, B/Z)
Output Leakage Current (Y, Z)
(Full Duplex Versions Only)
Output Leakage Current (Y, Z)
in Shutdown Mode (Full Duplex)
V_IH
V_IL
V_HYS
I_IN1
I_IN2
I_IN3
I_IN4
DE, DI, RE
DE, DI, RE
DE, DI, RE
DE = 0V, V_CC = 0V or 5.5V V_IN = 12V
V_IN = -7V
RE = 0V, DE = 0V, V_CC =
0V or 5.5V
V_IN = 12V
V_IN = -7V
RE = V_CC, DE = 0V, V_CC = V_IN = 12V
0V or 5.5V
V_IN = -7V
Full
2
-
-
V
Full
-
-
0.8
V
25
-
100
-
mV
Full
-2
-
2
µA
Full
-
70
125
µA
Full
-75
55
-
µA
Full
-
1
40
µA
Full
-40
-9
-
µA
Full
-
1
20
µA
Full
-20
-9
-
µA
5
FN6363.1
January 18, 2008