HI5714 Datasheet, PDF (5/13 Pages) Intersil Corporation – 8-Bit, 40/60/75/80 MSPS A/D Converter

HI5714
Electrical Specifications V_CCA = V_CCD = V_CCO = +5V; V_RB = 1.3V; V_RT = 3.6V; T_A = 25^oC,
Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITION
MIN
TYP
MAX
UNITS
HI5714/8 (f_CLK = 80MHz)
Bit Error Rate, BER
f_IN = 4.43MHz
f_IN = 7.5MHz
f_IN = 10MHz
(Note 7)
-
7.3
-
Bits
-
7.0
-
Bits
-
6.64
-
Bits
-
10^-11
-
Times/
Sample
TIMING (f_CLK = 75MHz) See Figures 1, 2
Sampling Delay, t_SD
Output Hold Time, t_HD
Output Delay Time, t_D
Output Delay Time, t_D
Output Enable Delay, t_PZH
Output Enable Delay, t_PZL
Output Disable Delay, t_PHZ
Output Disable Delay, t_PLZ
Aperture Jitter, t_AJ
POWER SUPPLY CHARACTERISTICS
HI5714/4/6/7
HI5714/8
Enable to High
Enable to Low
Disable from High
Disable from Low
-
-
2
ns
5
-
-
ns
-
10
13
ns
-
10
12.25
ns
-
14.6
-
ns
-
17.8
-
ns
-
5.3
-
ns
-
6.7
-
ns
-
50
-
ps
Analog Power Supply Range, V_CCA
Digital Power Supply Range, V_CCD
Output Power Supply Range, V_CCO
Total Supply Current
4.75
5.0
5.25
V
4.75
5.0
5.25
V
4.75
5.0
5.25
V
-
65
75
mA
Supply Current, I_CCA
Supply Current, I_CCD
Supply Current, I_CCO
Power Dissipation
-
30
-
mA
-
26
-
mA
-
9
-
mA
-
325
375
mW
NOTES:
1. Dissipation rating assumes device is mounted with all leads soldered to printed circuit board.
2. The supply voltages V_CCA and V_CCD may have any value between -0.3V and +6V as long as the difference V_CCA - V_CCD lies between
-0.3V and +0.3V.
3. In addition to a good layout of the digital and analog ground, it is recommended that the rise and fall times of the clock not be less than 1ns.
4. Analog input voltages producing code 00 up to and including FF.
V_OB (Bottom Offset Voltage) is the difference between the analog input which produces data equal to 00 and the Bottom Reference
Voltage (V_RB).
V_OBTC (Bottom Offset Voltage Temperature Coefficient) is the variation of V_OB with temperature.
V_OT (Top Offset Voltage) is the difference between the Top Reference Voltage (V_RT) and the analog input which produces data output
equal to FF.
V_OTTC (Top Offset Voltage Temperature Coefficient) is the variation of V_OT with temperature.
5. Input is standard 5 step video test signal. A 12-bit R reconstruct DAC and VM700 are used for measurement.
6. Full scale sinewave, f_IN = 4.43MHz.
7. f_CLK = 75MHz, f_IN = 4.43MHz, V_IN = ±8 LSB at code 128, 50% Clock duty cycle.
8. Parameter is guaranteed by design, not production tested.
5