FN6085 Datasheet, PDF (5/19 Pages) Intersil Corporation – ±15kV ESD, 5V, Full Fail-Safe, 1/8 Unit Load, RS-485/RS-422 Transceivers

ISL83080E, ISL83082E, ISL83083E, ISL83084E, ISL83085E, ISL83086E, ISL83088E
Absolute Maximum Ratings
V_CC to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Input Voltages
DI, DE, RE . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to (V_CC + 0.3V)
Input/Output Voltages
A, B, Y, Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -9V to +13V
A, B, Y, Z (Transient Pulse Through 100Ω, Note 14) . . . . . . ±75V
RO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to (V_CC + 0.3V)
Short Circuit Duration
Y, Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . See Specification Table
Thermal Information
Thermal Resistance (Typical, Note 3)
θ_JA (°C/W)
8 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . .
105
8 Ld MSOP Package . . . . . . . . . . . . . . . . . . . . . . . .
140
10 Ld MSOP Package . . . . . . . . . . . . . . . . . . . . . . .
190
14 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . .
128
Maximum Junction Temperature (Plastic Package) . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTE:
3. θ_JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications Test Conditions: V_CC = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at V_CC = 5V, T_A = +25°C
(Note 5).
PARAMETER
SYMBOL
TEST CONDITIONS
TEMP MIN
MAX
(°C) (Note 4) TYP (Note 4) UNITS
DC CHARACTERISTICS
Driver Differential V_OUT (no load)
Driver Differential V_OUT (with load)
Change in Magnitude of Driver
Differential V_OUT for
Complementary Output States
V_OD1
V_OD2
ΔV_OD
R_L = 100Ω (RS-422) (Figure 1A)
R_L = 54Ω (RS-485) (Figure 1A)
R_L = 60Ω, -7V ≤ V_CM ≤ 12V (Figure 1B)
R_L = 54Ω or 100Ω (Figure 1A)
Full
-
Full
2
-
V_CC
V
2.9
-
V
Full
1.5
2.4
V_CC
V
Full
1.5
2.6
-
V
Full
-
0.01
0.2
V
Driver Common-Mode V_OUT
Change in Magnitude of Driver
Common-Mode V_OUT for
Complementary Output States
V_OC
ΔV_OC
R_L = 54Ω or 100Ω (Figure 1A)
R_L = 54Ω or 100Ω (Figure 1A)
Full
-
2.85
3
V
Full
-
0.01
0.1
V
Logic Input High Voltage
V_IH
DE, DI, RE
Full
2
-
-
V
Logic Input Low Voltage
V_IL
DE, DI, RE
Full
-
-
0.8
V
DI Input Hysteresis Voltage
V_HYS
25
-
100
-
mV
Logic Input Current
I_IN1
DE, DI, RE
Full
-2
-
2
µA
Input Current (A, B)
I_IN2
DE = 0V, V_CC = 0V or 5.5V V_IN = 12V
Full
-
70
125
µA
V_IN = -7V
Full
-75
55
-
µA
Output Leakage Current (Y, Z) (Full
Duplex Versions Only)
I_IN3
RE = 0V, DE = 0V, V_CC = 0V V_IN = 12V
or 5.5V (Note 13)
V_IN = -7V
Full
-
7
125
µA
Full
-75
11
-
µA
Output Leakage Current (Y, Z)
in Shutdown Mode (Full Duplex)
I_IN3
RE = V_CC, DE = 0V,
V_IN = 12V
V_CC = 0V or 5.5V (Note 13) _{VIN = -7V}
Full
-
0
Full
-20
9
20
µA
-
µA
Driver Short-Circuit Current,
V_O = High or Low
I_OSD1 DE = V_CC, -7V ≤ V_Y or V_Z ≤ 12V (Note 7)
Full
-
-
±250
mA
5
FN6085.9
April 22, 2008