X9C103SIZT1 Datasheet, PDF (4/10 Pages) Intersil Corporation – Wiper Position Stored in Non-volatile Memory and Recalled on Power-up

X9C102, X9C103, X9C104, X9C503
Absolute Maximum Ratings
Voltage on CS, INC, U/D and V_CC with Respect to V_SS . -1V to +7V
Voltage on V_H/R_H and V_L/R_L Referenced to V_SS. . . . . . . -8V to +8V
ΔV = |V_H/R_H - V_L/R_L|
X9C102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4V
X9C103, X9C104, and X9C503 . . . . . . . . . . . . . . . . . . . . . . . .10V
I_W (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.8mA
Power Rating
X9C102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16mW
X9C103 X0C104, and X9C503 . . . . . . . . . . . . . . . . . . . . . .10mW
Thermal Information
Temperature Under Bias . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
*Pb-free PDIPs can be used for through-hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
Recommended Operating Conditions
Commercial Temperature Range. . . . . . . . . . . . . . . . . 0°C to +70°C
Industrial Temperature Range . . . . . . . . . . . . . . . . . .-40°C to +85°C
Supply Voltage Range (V_CC) . . . . . . . . . . . . . . . . . . . . . . . 5V ±10%
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
Electrical Specifications Over recommended operating conditions unless otherwise stated.
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
TYP
MIN
(Note 6)
MAX
UNIT
POTENTIOMETER CHARACTERISTICS
R_TOTAL
V_VH/RH
V_VL/RL
I_W
R_W
End-to-End Resistance Variation
V_H Terminal Voltage
V_L Terminal Voltage
Wiper Current
Wiper Resistance
Resistor Noise (Note 7)
Wiper Current = ±1mA
Ref 1kHz
-20
-5
-5
-4.4
40
-120
+20
%
+5
V
+5
V
4.4
mA
100
Ω
dBV
Charge Pump Noise (Note 7)
Resolution
@ 850kHz
20
mV_RMS
1
%
Absolute Linearity (Note 3)
Relative Linearity (Note 4)
R_TOTAL Temperature Coefficient
R_TOTAL Temperature Coefficient
Ratiometric Temperature Coefficient
V_W(n)(actual) - V_{W(n)(EXPECTED)}
V_{W(n + 1)(ACTUAL)} - [V_{W(n) + MI}]
X9C103, X9C503, X9C104
X9C102
-1
+1 MI (Note 5)
-0.2
+0.2 MI (Note 5)
±300 (Note 7)
ppm/°C
±600 (Note 7)
ppm/°C
±20
ppm/°C
C_H/C_L/C_W Potentiometer Capacitances
See “Circuit #3 SPICE Macro
10/10/25
pF
(Note 7)
Model” on page 5.
DC OPERATING CHARACTERISTICS
I_CC
V_CC Active Current
CS = VIL, U/D = V_IL or V_IH and
INC = 0.4V to 2.4V at Max t_CYC
I_SB
Standby Supply Current
CS = V_CC - 0.3V, U/D and
INC = V_SS or V_CC - 0.3V
I_LI
CS, INC, U/D Input Leakage Current
V_IN = V_SS to V_CC
V_IH
CS, INC, U/D input HIGH Voltage
2
V_IL
CS, INC, U/D input LOW Voltage
C_IN
CS, INC, U/D Input Capacitance (Note 7) V_CC = 5V, V_IN = V_SS, T_A = +25°C,
f = 1MHz
1
3
mA
200
750
µA
±10
µA
V
0.8
V
10
pF
4
FN8222.3
July 20, 2009