ISL72027SEH Datasheet, PDF (4/18 Pages) Intersil Corporation – 3.3V Radiation Tolerant CAN Transceiver, 1Mbps, Listen Mode, Split Termination Output

ISL72027SEH
Absolute Maximum Ratings
VCC to GND with/without Ion Beam. . . . . . . . . . . . . . . . . . . . . -0.3V to 4.5V
CANH, CANL, VREF Under Ion Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18V
CANH, CANL, VREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20V
I/O Voltages
D, R, RS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V
Receiver Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10mA to 10mA
Output Short-circuit Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
ESD Rating:
Human Body Model (Tested per MIL-PRF-883 3015.7)
CANH, CANL Bus Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4kV
All Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4kV
Charged Device Model (Tested per JESD22-C101D) . . . . . . . . . . . . . . 750V
Machine Model (Tested per JESD22-A115-A) . . . . . . . . . . . . . . . . . . . . 200V
Thermal Information
Thermal Resistance (Typical)
_JA (°C/W) _JC (°C/W)
8 Ld FP Package (Notes 3, 4) Direct Attach .
39
7
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .+175°C
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Recommended Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55°C to +125°C
V_CC Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3V to 3.6V
Voltage on CAN I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7V to 12V
V_IH D Logic Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 5.5V
V_IL D Logic Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to 0.8V
IOH Driver (CANH - CANL = 1.5V, V_CC = 3.3V) . . . . . . . . . . . . . . . . . . - 40mA
IOH Receiver (V_OH = 2.4V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -4mA
IOL Driver (CANH - CANL = 1.5V, V_CC = 3.3V) . . . . . . . . . . . . . . . . . . +40mA
IOL Receiver (V_OL = 0.4V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4mA
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
3. _JA is measured with the component mounted on a high effective thermal conductivity test board (two buried 1oz copper planes) with “direct attach”
features package base mounted to PCB thermal land with a 10mil gap fill material having a k of 1W/m-K. See Tech Brief TB379.
4. For _JC, the “case temp” location is the center of the package underside.
Electrical Specifications Test Conditions: V_CC = 3V to 3.6V; Typicals are at T_A = +25°C (Note 7); unless otherwise specified (Note 5).
Boldface limits apply across the operating temperature range, -55°C to +125°C or across a total ionizing dose of 75krad(Si) at +25°C with exposure at
a low dose rate of <10mrad(Si)/s.
PARAMETER
SYMBOL
TEST CONDITIONS
TEMP MIN
TYP
MAX
(°C) (Note 6) (Note 7) (Note 6)
UNIT
DRIVER ELECTRICAL CHARACTERISTICS
Dominant Bus Output Voltage V_O(DOM) D = 0V, CANH, RS = 0V,
3V  V_CC  3.6V
Full 2.25
2.85
V_CC
V
Figures 10 and 11
D = 0V, CANL, RS = 0V,
Figures 10 and 11
Full 0.10
0.65
1.25
V
Recessive Bus Output Voltage V_O(REC)
D = 3V, CANH, RS = 0V, 60Ω 3V  V_CC  3.6V
Full 1.80
2.30
2.70
V
and no load, Figures 10 and
11
D = 3V, CANL, RS = 0V, 60Ω
and no load, Figures 10 and
11
Full 1.80
2.30
2.80
V
Dominant Output Differential V_OD(DOM) D = 0V, RS = 0V, 3V V_CC  3.6V, Figures 10 and 11 Full
1.5
2.2
3.0
V
Voltage
D = 0V, RS = 0V, 3V V_CC  3.6V, Figures 11 and 12 Full
1.2
2.1
3.0
V
Recessive Output Differential V_OD(REC) D = 3V, RS = 0V, 3V V_CC  3.6V, Figures 10 and 11 Full
-120
0.2
Voltage
D = 3V, RS = 0V, 3.0V V_CC  3.6V, no load
Full -500
-34
12
mV
50
mV
Logic Input High Voltage (D) V_IH
3V V_CC  3.6V, Note 8
Full
2.0
-
5.5
V
Logic Input Low Voltage (D)
V_IL
3V V_CC  3.6V, Note 8
Full
0
-
0.8
V
High Level Input Current (D)
I_IH
D = 2V, 3V  V_CC  3.6V
Full
-30
-3
30
µA
Low Level Input Current (D)
I_IL
D = 0.8V, 3V  V_CC  3.6V
Full
-30
-7
30
µA
RS Input Voltage for Listen
Mode
V_IN(RS)
3V  V_CC  3.6V
Full 0.75xVCC 1.90
5.5
V
Submit Document Feedback
4
FN8763.1
November 9, 2015