ISL59911 Datasheet, PDF (4/17 Pages) Intersil Corporation – 250MHz Triple Differential Receiver/ Equalizer with I2C Interface

ISL59911
Absolute Maximum Ratings (T_A = +25°C)
V+ = V+_R = V+_G = V+_B, V- = V-_R = V-_G = V-_B = V-_D
Supply Voltage between V+ and V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V
Maximum Absolute Slew Rate of V+ and V- . . . . . . . . . . . . . . . . . . . ±1V/µs
Maximum Continuous Output Current per Channel . . . . . . . . . . . . . ±30mA
Power Dissipation. . . . . . . . . . . . . . . . See “Power Dissipation” on page 12
Pin Voltages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V- - 0.5V to V+ + 0.5V
ESD Ratings
Human Body Model (tested per JESD22-A114) . . . . . . . . . . . . . . . 7000V
Machine Model (Tested per JESD22-A115). . . . . . . . . . . . . . . . . . . . 300V
Charged Device Model (Tested per JESD22C101C) . . . . . . . . . . . . 2000V
Latch Up (Tested per JESD78; Class II, Level A) . . . . . . . . . . . . . . . . . . . . 100mA
Thermal Information
Thermal Resistance (Typical)
θ_JA (°C/W) θ_JC (°C/W)
32 Ld QFN (Notes 5, 6) . . . . . . . . . . . . . . . .
31
2.1
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Die Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
V+ Supply Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 5.5V
V- Supply Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -4.5V to -5.5V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
5. θ_JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
6. For θ_JC, the “case temp” location is the center of the exposed metal pad on the package underside.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are
at the specified temperature and are pulsed tests, therefore: T_J = T_C = T_A
Electrical Specifications V+ = V+_R = V+_G = V+_B = +5V, V- = V-_R = V-_G = V-_B = V-_D = -5V, T_A = +25°C, all registers at default settings
(equalizer stages set to minimum boost, noise filter set to max bandwidth, x2 gain mode, GAIN_DC = 0dB), all analog inputs at 0V, auto offset
calibration executed, R_L = 5pF || (75Ω + 75Ω) to GND, thermal pad connected to -5V, unless otherwise specified.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
MAX
(Note 7) TYP (Note 7) UNIT
POWER SUPPLY
Positive Supply
Voltage (V+)
V+ = V+_R = V+_G = V+_B
4.5
5.5
V
Negative Supply V- = V-_R = V-_G = V-_B = V-_D
Voltage (V-)
-4.5
-5.5
V
Operating Current Sum of currents into all V+ pins
(I_D+)
Operating Current Sum of currents out of all V- pins,
(I_D-)
including thermal pad
Disabled Current Sum of currents into all V+ pins
(I_D+_DISABLED)
Disabled Current Sum of currents into all V- pins,
(I_D-_DISABLED)
including thermal pad
PSRR_DC
Power Supply Rejection Ratio
AC PERFORMANCE
ENABLE = 0V
ENABLE = 0V
110
105
2.5
0.35
55
140 mA
130
mA
3.5
mA
2.5
mA
dB
BW
Full Power Bandwidth
250
MHz
GAIN_100MHz
GAIN_20MHz
GAIN_6MHz
GAIN_1MHz
GAIN_0.2MHz
GAIN_DC
f_{NOISE_MIN}
f_{NOISE_MAX}
SR_DIFF
THD
Maximum Boost @ 100MHz
All three 100MHz filters set to maximum
Maximum Boost @ 20MHz
20MHz filter set to maximum
Maximum Boost @ 6MHz
6MHz filter set to maximum
Maximum Boost @ 1MHz
1MHz filter set to maximum
Maximum Boost @ 200kHz
200kHz filter set to maximum
DC Gain Adjustment Range
-3dB Corner Freq of Noise Filter, High Noise Filter Register = 0x0
-3dB Corner Freq of Noise Filter, Low Noise Filter Register = 0xF
Output Slew Rate
Total Harmonic Distortion
V_IN = -1V to +1V
f = 10MHz, 0.7V_P-P input sine wave
26
9.5
7.5
3.1
0.75
±4
250
50
1
-45
-60
dB
dB
dB
dB
dB
dB
MHz
MHz
V/ns
dBc
4
FN7548.0
September 2, 2011