ISL54406 Datasheet, PDF (4/16 Pages) Intersil Corporation – Stereo Click and Pop Eliminator with Audio Muting

ISL54406
Absolute Maximum Ratings
V_DD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 5.5V
Input Voltages
L_IN, R_IN (Note 6). . . . . . . . . . . . . . -2V to ((V_DD) + 0.3V)
SEL1 (Note 6) . . . . . . . . . . . . . . . -0.3V to ((V_DD) + 0.3V)
SEL2 (Note 6) . . . . . . . . . . . . . . . -0.3 to ((V_DD) + 0.3V)
Output Voltages
L_OUT, R_OUT (Note 6) . . . . . . . . . . . -2V to ((V_DD) + 0.3V)
Continuous Current . . . . . . . . . . . . . . . . . . . . . . ±150mA
Peak Current
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . ±300mA
ESD Rating:
Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . >5kV
Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . >300V
Charged Device Model . . . . . . . . . . . . . . . . . . . . . >1.5kV
Latch-up Tested per JEDEC; Class II Level A . . . . . at +85°C
Thermal Information
Thermal Resistance (Typical)
θ_JA (°C/W) θ_JC (°C/W)
10 Ld µTQFN (Note 7, 8) . . . . . . . . 160
105
10 Ld TDFN (Notes 9, 10) . . . . . . .
55
18
Maximum Junction Temperature (Plastic Package). . +150°C
Maximum Storage Temperature Range. . . . . -65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . -40°C to +85°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact
product reliability and result in failures not covered by warranty.
NOTES:
6. Signals on LIN, RIN, LOUT, ROUT, SEL1, and SEL2 exceeding V_DD or GND by specified amount are clamped. Limit current to
maximum current ratings.
7. θ_JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief
TB379 for details.
8. For θ_JC, the “case temp” location is taken at the package top center.
9. θ_JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach”
features. See Tech Brief TB379.
10. For θ_JC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: V_DD = +3.0V, GND = 0V, V_{SELx_H} = 1.4V,
V_{SELx_L}= 0.5V, (Notes 11), Unless Otherwise Specified
Boldface limits apply over the operating temperature range,
-40°C to +85°C.
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 12, 13) TYP (Notes 12, 13) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Input Signal Range, V_DD = 3.3V, V_SEL2 = 1.4V, V_SEL1 = 1.4V Full
-1.5
-
1.5
V
V_ANALOG
ON-Resistance, r_ON
V_DD = 3.0V, V_SEL2 = 1.4V, V_SEL1 = 1.4V +25
-
2.5
2.8
Ω
I_XOUT = 40mA, V_LIN or V_RIN = -0.85V to
0.85V, (See Figure 2, Note 16)
Full
-
-
4.0
Ω
r_ON Flatness, r_FLAT(ON)
V_DD = 3.0V, V_SEL2 = 1.4V, V_SEL1 = 1.4V +25
-
2
-
mΩ
I_XOUT = 40mA, V_LIN or V_RIN = -0.85V to
0.85V, (Notes 14, 16)
Full
-
-
mΩ
r_ON Matching Between
Channels, Δr_ON
V_DD = 3.0V, V_SEL2 = 1.4V, V_SEL1 = 1.4V
I_XOUT = 40mA, V_LIN or V_RIN = Voltage at
max r_ON over signal range of -0.85V to
0.85V, (Note 15, 16)
+25
Full
-
0.09
0.25
Ω
-
-
0.35
Ω
Discharge Pull-Down
V_DD = 3.6V, V_SEL2 = 1.4V, V_SEL1= 1.4V , +25
-
240
-
kΩ
Resistance, R_L, R_R
V_ROUT or V_LOUT = -0.85V, 0.85V. Measure
current through the discharge pull down
resistor and calculate resistance value.
Click and Pop Discharge
V_DD = 3.0V, V_SEL2 = 0V, V_SEL1= 1.4V,
+25
-
35
-
Ω
Resistance
V_INL or V _INR = -0.85V, 0.85V. Measure
current through the Click and Pop
discharge resistance and calculate
resistance value.
4
FN6578.1
July 14, 2010