English
Language : 

ISL23511_15 Datasheet, PDF (4/11 Pages) Intersil Corporation – Low Noise, Low Power, 32 Taps, Push Button Controlled Potentiometer
ISL23511
Potentiometer Specifications Over recommended operating conditions, unless otherwise specified. (Continued)
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
(Note 18) (Note 5) (Note 18) UNIT
RDNL
(Note 14)
Differential Non-linearity
W and U option
-0.5
0.5
MI
(Note 12)
Roffset
(Note 13)
Offset
W option
U option
0
1
3
MI
(Note 12)
0
0.5
1
MI
(Note 12)
DC Electrical Specifications Over recommended operating conditions unless otherwise specified.
SYMBOL
ICC
PARAMETER
VCC Active Current
TEST CONDITIONS
VCC = 5.5V, perform wiper move
operation
MIN
(Note 18)
TYP
(Note 5)
MAX
(Note 18)
150
ISB
ILkg
VIH
VIL
CIN
(Note 17)
Rpull_up
(Note 17)
Standby Current
PU, PD Input Leakage Current
PU, PD Input HIGH Voltage
PU, PD input LOW Voltage
PU, PD Input Capacitance
Pull-up Resistor for PU and PD
0.6
3
VIN = VSS to VCC
-2
+2
VCC x 0.7
VCC x 0.1
VCC = 3.3V, TA = +25°C, f = 1MHz
10
1
UNIT
µA
µA
µA
V
V
pF
M
AC Electrical Specifications Over recommended operating conditions unless otherwise specified.
SYMBOL
PARAMETER
MIN
(Note 18)
TYP
(Note 5)
MAX
(Note 18)
UNIT
tGAP
Time Between Two Separate Push Button Events
2
ms
tDB
Debounce Time
15
30
ms
tS SLOW Wiper Change on a Slow Mode
100
250
375
ms
tS FAST Wiper Change on a Fast Mode
25
50
75
ms
tstdn
Time to Enter Shutdown Mode (keep PU and PD LOW)
2
s
(Note 17)
tR VCC
NOTES:
VCC Power-up Rate
0.2
50
V/ms
5. Typical values are for TA = +25°C and 3.3V supply voltage.
6. LSB: [V(RW)31 – V(RW)0]/31. V(RW)31 and V(RW)0 are voltage on RW pin for the DCP register set to 1F hex and 00 hex respectively. LSB is
the incremental voltage when changing from one tap to an adjacent tap.
7. ZS error = V(RW)0/LSB.
8. FS error = [V(RW)31 – VCC]/LSB.
9. DNL = [V(RW)i – V(RW)i-1]/LSB -1, for i = 1 to 31; i is the DCP register setting.
10. INL = [V(RW)i – i • LSB – V(RW)]/LSB for i = 1 to 31
11.
TCV
=
-------M-----a----x------V-------R-----W--------i-----–-----M-----i--n------V-------R-----W--------i--------
MaxVRWi + MinVRWi  2

------1---0----6------- for i = 5 to 31 decimal, T = -40°C to +125°C.
+165°Cvoltage and Min ( ) is the minimum value of the
Max(
wiper
) is the maximum value of the wiper
voltage over the temperature range.
12. MI = |RW31 – RW0|/31. MI is a minimum increment. RW31 and RW0 are the measured resistances for the DCP register set to 1F hex and 00
hex respectively.
13. Roffset = RW0/MI, when measuring between RW and RL.
Roffset = RW31/MI, when measuring between RW and RH.
14. RDNL = (RWi – RWi-1)/MI, for i = 1 to 31.
15. RINL = [RWi – (MI • i) – RW0]/MI, for i = 1 to 31.
16.
TCR
=
-------M-----a----x------R-----i-----–-----M-----i--n------R-----i--------
MaxRi + MinRi  2

+----1--1--6-0--5--6--°--C---thefomrini =im5umto
31, T
value
= -40°C to +125°C. Max( )
of the resistance over the
is the maximum value
temperature range.
of
the
resistance
and
Min
(
)
is
17. Limits should be considered typical and are not production tested.
18. Parts are 100% tested at +25°C. Over-temperature limits established by characterization and are not production tested.
4
FN6588.2
September 9, 2015