X93254_08 Datasheet, PDF (3/8 Pages) Intersil Corporation – Dual Digitally Controlled Potentiometers(XDCPs™)

X93254
Absolute Maximum Ratings
Voltage on CS, INC, U/D, R_H, R_L and V_CC
with respect to V_SS . . . . . . . . . . . . . . . . . . . . . . . . . . -1V to +6.5V
Maximum resistor current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2mA
Recommended Operating Conditions
Temperature Range
Industrial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Supply Voltage
V_CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3V ±10% (Note 6)
Thermal Information
Temperature under bias. . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Lead temperature (soldering 10s) . . . . . . . . . . . . . . . . . . . . . +300°C
Maximum reflow temperature (40s) . . . . . . . . . . . . . . . . . . . . +240°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1. Absolute linearity is utilized to determine actual wiper voltage versus expected voltage = (VH(n)(actual) - VH(n)(expected)) = ±1 Ml Maximum.
n = 1 .. 29 only
2. Relative linearity is a measure of the error in step size between taps = VH(n+1) - [VH(n) + Ml] = ±0.5 Ml, n = 1 .. 29 only.
3. 1 Ml = Minimum Increment = RTOT/31.
4. Typical values are for T_A = +25°C and nominal supply voltage.
5. Limits established by characterization and are not production tested.
6. When performing multiple write operations, V_CC must not decrease by more than 150mV from its initial value.
7. Parts are 100% tested at +25°C. Over-temperature limits established by characterization and are not production tested.
Potentiometer Specifications Over recommended operating conditions, unless otherwise stated.
SYMBOL
PARAMETER
TEST CONDITIONS/NOTES
MIN
(Note 7)
R_TOT
End-to-End Resistance
37.5
V_R
R_H, R_L Terminal Voltages
0
Power Rating
R_TOTAL = 50kΩ
Noise
Ref: 1kHz
R_W
Wiper Resistance
I_W
Wiper Current
Resolution
Absolute Linearity (Note 1)
Relative Linearity (Note 2)
C_H/C_L/C_W
R_TOTAL Temperature Coefficient
Potentiometer Capacitances
(Note 5)
(Note 5)
V_H(n)(actual) - V_{H(n)(expected)}
V_H(n+1) - [V_H(n)+MI
(Note 5)
See “Circuit #2 SPICE Macro
Model” on page 4
TYP
(Note 4)
50
-120
3
±35
10/10/25
MAX
(Note 7)
UNIT
62.5
kΩ
V_CC
1
V
mΩ
(Note 5)
dBV
(Note 5)
1000
Ω
0.6
mA
%
±1
MI
(Note 3)
±0.5
MI
(Note 3)
ppm/°C
pF
(Note 5)
3
FN8186.1
February 4, 2008