ISL59910_14 Datasheet, PDF (3/12 Pages) Intersil Corporation – Triple Differential Receiver/Equalizer

ISL59910, ISL59913
Absolute Maximum Ratings (T_A = +25°C)
Supply Voltage between V_S+ and V_S- . . . . . . . . . . . . . . . . . . . . .12V
Maximum Continuous Output Current per Channel. . . . . . . . . 30mA
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
Pin Voltages . . . . . . . . . . . . . . . . . . . . . . . . . V_S- -0.5V to V_S+ +0.5V
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Operating Conditions
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Die Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +150°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are
at the specified temperature and are pulsed tests, therefore: T_J = T_C = T_A
Electrical Specifications V_SA+ = V_A+ = +5V, V_SA- = V_A- = -5V, T_A = +25°C, exposed die plate = -5V, unless otherwise specified.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
TYP
MAX UNIT
AC PERFORMANCE
BW
Bandwidth
(See Figure 1)
150
MHz
SR
Slew Rate
V_IN = -1V to +1V, V_G = 0.39, V_C = 0,
1.5
R_L = 75 + 75Ω
THD
Total Harmonic Distortion
10MHz 2V_P-P out, V_G = 1V, X2 gain, V_C = 0
-50
DC PERFORMANCE
kV/µs
dBc
V(V_OUT)_OS Offset Voltage
X2 = high, no equalization
ΔV_OS
Channel-to-Channel Offset Matching X2 = high, no equalization
INPUT CHARACTERISTICS
-110
-15
+110
mV
-140
0
+140
mV
CMIR
Common-Mode Input Range
-4/+3.5
V
O_NOISE
Output Noise
V_G = 0V, V_C = 0V, X2 = HIGH, R_LOAD = 150Ω,
-110
Input 50Ω to GND, 10MHz
dBm
CMRR
Common-Mode Rejection Ratio
Measured at 10kHz
-80
dB
CMRR
Common-Mode Rejection Ratio
Measured at 10MHz
-55
dB
CMBW
CM Amplifier Bandwidth
10k || 10pF load
50
MHz
CM_SLEW
CM Slew Rate
C_INDIFF
Differential Input Capacitance
R_INDIFF
Differential Input Resistance
C_INCM
CM Input Capacitance
R_INCM
CM Input Resistance
+I_IN
Positive Input Current
-I_IN
Negative Input Current
V_INDIFF
Differential Input Range
OUTPUT CHARACTERISTICS
Measured @ +1V to -1V
Capacitance V_INP to V_INM
Resistance V_INP to V_INM
Capacitance V_INP = V_INM to GND
Resistance V_INP = V_INM to GND
DC bias @ V_INP = V_INM = 0V
DC bias @ V_INP = V_INM = 0V
V_INP - V_INM when slope gain falls to 0.9
100
600
1
1.2
1
1
1
2.5
V/µs
fF
MΩ
pF
MΩ
µA
µA
V
V(V_OUT)
Output Voltage Swing
R_L = 150Ω
±3.5
V
I(V_OUT)
Output Drive Current
R_L = 10Ω, V_INP = 1V, V_INM = 0V, X2 = high,
50
60
mA
V_G = 0.39
R(V_CM)
CM Output Resistance of
VCM_R/G/B (ISL59913 only)
at 100kHz
30
Ω
Gain
ΔGain @ DC
ΔGain @
15MHz
Gain
Channel-to-Channel Gain Matching
Channel-to-Channel Gain Matching
V_C = 0, V_G = 0.39, X2 = 5, R_L = 150Ω
V_C = 0, V_G = 0.39, X2 = 5, R_L = 150Ω
V_C = 0.6, V_G = 0.39, X2 = 5, R_L = 150Ω,
Frequency = 15MHz
0.85
1.0
1.1
3
8
%
3
11
%
V(SYNC)_HI
High Level output on V/H_OUT
(ISL59910 only)
V(V_SP)
- 0.1V
V(V_SP)
3
FN6406.0
December 15, 2006