ISL59831 Datasheet, PDF (3/11 Pages) Intersil Corporation – Single Supply Video Driver with Reconstruction Filter and Charge Pump

ISL59831
Absolute Maximum Ratings (T_A = +25°C)
V_CC to GND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4V
V_IN to GND . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to V_CC + 0.3V
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . ±50mA
Maximum Current into Any Pin . . . . . . . . . . . . . . . . . . . . . . . ±50mA
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3015.7) . . .3500V
Machine Model (Per EIAJ ED-4701 Method C-111) . . . . . . . .350V
Thermal Information
Thermal Resistance (Typical, Notes 1, 2) θ_JA (°C/W) θ_JC (°C/W)
4x3 TDFN Package . . . . . . . . . . . . . . .
41
3.5
Maximum Junction Temperature (Plastic Package) . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . +300°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: T_J = T_C = T_A
NOTES:
1. θ_JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379.
2. θ_JC, “case temperature” location is at the center of the exposed metal pad on the package underside. See Tech Brief TB379.
Electrical Specifications V_CP = V_CC = 3.3V, C_F = 56nF ±20%, C_S = 0.1µF ±20%, R_FIL = 20Ω ±1%, C_FIL = 0.22µF ±20%,
C_IN = 0.1µF ±20%, R_L = 150Ω, C_L = 0pF, T_A = +27°C, unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
DC CHARACTERISTICS
V_CC, V_CP Supply Range
CPVEE Charge Pump Output
3.0
3.3
3.6
V
-1.1
-1.9
-2.4
V
I_CC
Supply Current
No load
I_CP
Charge Pump Supply No load
Current
4
6
8.5
mA
5
9
20
mA
I_PD
Power Down Current ENABLE = 0.4V
I_IN
Input Pulldown Current V_IN = 0.5V
A_V
DC Gain
V_{IN_MAX} Max DC Input Range DC-Coupled Input, guaranteed by output linearity
V_CLAMPOUT Output Sync Tip Clamp Sync height = 293mV, V_IN ≤ 0, AC-coupled input
Level
0.5
1.9
1.4
-500
2
2
2
-550
5
µA
4.5
µA
2.06
V/V
V
-600
mV
VCLAMPIN Input Clamp Level
Input floating
0
40
80
mV
V_OS Output Level Shift
Sync height = 293mV, V_IN > 0, output shifted relative to input,
DC-coupled input
-530
-592
-650
mV
I_CLAMP Clamp Restore Current Force V_IN = -0.3V
PSRR_DC Power Supply Rejection VCC = +3.0 to +3.6
AC CHARACTERISTICS
2
3.9
mA
35
50
dB
A_PB Passband Flatness
f = 100kHz to 5MHz relative to 100kHz
A_SB Stopband Attenuation f ≥ 27MHz relative to 100kHz
dG
Differential Gain
5-step modulated staircase
0
25
44
0.4
2
dB
dB
%
dP
Differential Phase
5-step modulated staircase
0.35
°
SNR Signal to Noise Ratio Peak signal (1.4V_P-P) to RMS noise, f = 10Hz to 50MHz
59
dB
3
FN6266.0
March 29, 2007