ISL59534 Datasheet, PDF (3/22 Pages) Intersil Corporation – 32x16 Video Crosspoint

ISL59534
Absolute Maximum Ratings (T_A = +25°C)
Supply Voltage between V_S and GND. . . . . . . . . . . . . . . . . . . . 6.0V
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 40mA
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . +125°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Maximum power supply (V_S) slew rate . . . . . . . . . . . . . . . . . . 1V/μs
ESD Classification
Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500V
Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100V
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: T_J = T_C = T_A
DC Electrical Specifications V_S = 5V, R_L = 150Ω unless otherwise noted.
PARAMETER
DESCRIPTION
CONDITION
V_S
V_SDO
A_V
GM
V_IN
V_OUT
I_B
I_REF
V_OS
I_OUT
PSRR
I_S
Power Supply Voltage
Power Supply for SDO output pin
Establishes serial data output high level
Gain (between all primary inputs and all
overlay inputs)
Gain Matching (to average of all other
outputs)
Video Input Voltage Range
Video Output Voltage Range
Input Bias Current
A_V = 1
A_V = 2
A_V = 1
A_V = 2
A_V = 1
A_V = 2
Clamp function disabled (DC coupled inputs)
V_REF Input Current
Output Offset Voltage
Output Current
Power Supply Rejection Ratio
Supply Current
Clamp function enabled, V_IN = V_REF + 0.5V
Clamp function enabled
A_V = 1
A_V = 2
Sourcing, R_L = 10Ω to GND
Sinking, R_L = 10Ω to 2.5V
A_V = 2
Enabled, all outputs enabled, no load current
Enabled, all outputs disabled, no load current
Disabled
MIN
4.5
1.2
0.98
1.96
-1.5
-1.5
0
0.1
-10
0.5
-20
-100
60
24
50
385
280
1.2
TYP
1
2
-5
2
-110
8
-24
108
31
70
445
320
1.8
MAX
5.5
5.5
1.02
2.04
+1.5
+1.5
3.5
3.8
1
10
35
40
505
360
2.4
UNIT
V
V
V/V
V/V
%
%
V
V
µA
µA
µA
mV
mV
mA
mA
dB
mA
mA
mA
AC Electrical Specifications V_S = 5V, R_L = 150Ω unless otherwise noted.
PARAMETER
DESCRIPTION
CONDITION
MIN TYP MAX UNIT
BW -3dB
BW 0.1dB
SR
T_S
Glitch
T_over
dG
dP
3dB Bandwidth
0.1dB Bandwidth
Slew Rate
Settling Time to 0.1%
Switching Glitch, Peak
Overlay Delay Time
Diff Gain
Diff Phase
V_OUT = 200mV_P-P, A_V = 2
300
MHz
V_OUT = 200mV_P-P, A_V = 2
V_OUT = 2V_P-P, A_V = 2
V_OUT = 2V_P-P, A_V = 2
50
MHz
300
520
740 V/µs
12
ns
A_V = 1
40
mV
From OVER rising edge to output transition
6
ns
A_V = 2, R_L = 150Ω
A_V = 2, R_L = 150Ω
0.025
%
0.05
°
Xt
Hostile Crosstalk
6MHz
-85
dB
V_N
Input Referred Noise Voltage
18
nV/√Hz
3
FN6249.5
February 7, 2007