English
Language : 

ISL54065_14 Datasheet, PDF (3/15 Pages) Intersil Corporation – Negative Signal Swing, Sub-ohm, Dual SPDT with Click and Pop Elimination Single Supply Switch with Enable Pin
◁
ISL54065
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 7.0V
Input Voltages
NOx, NCx (Note 2) . . . . . . . . . . . . . . . . (V+ - 7V) to ((V+) + 0.5V)
INx, EN (Note 2) . . . . . . . . . . . . . . . . . . . . . . -0.5 to ((V+) + 0.5V)
Output Voltages
COMx (Note 2) . . . . . . . . . . . . . . . . . . . (V+ - 7V) to ((V+) + 0.5V)
Continuous Current NOx, NCx, or COMx . . . . . . . . . . . . . . ±300mA
Peak Current NOx, NCx, or COMx
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . ±500mA
ESD Rating:
Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>6kV
Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>400V
Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . >1.5kV
Thermal Information
Thermal Resistance (Typical)
θJA (°C/W)
12 Ld µTQFN Package (Note 3) . . . . . . . . . . . . . . .
155
Maximum Junction Temperature (Plastic Package). . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Power Supply Range . . . . . . . . . . . . . . . . . . . . . . . . +1.8V to +6.5V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
2. Signals on NCx, NOx, INx, EN, CP, or COMx exceeding V+ or GND by the specified amount are clamped by internal diodes. Limit forward diode
current to maximum current ratings.
3. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 5V Supply Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V, VEN = VINH,
VCP = VINL (Note 4), unless otherwise specified.
PARAMETER
TEST CONDITIONS
TEMP
MIN
(°C) (Notes 5, 6)
TYP
MAX
(Notes 5, 6) UNITS
ANALOG SWITCH CHARACTERISTICS
ON-Resistance, rON
V+ = 4.5V, ICOM = 100mA, VNO or
VNC = (V+ -6.5) to V+ (see Figure 5)
25
-
0.52
-
Ω
Full
-
0.68
-
Ω
rON Matching Between Channels, V+ = 4.5V, ICOM = 100mA, VNO or VNC = Voltage 25
-
10
-
mΩ
ΔrON
at max rON (Note 8)
Full
-
13.1
-
mΩ
rON Flatness, RFLAT(ON)
V+ = 4.5V, ICOM = 100mA, VNO or
VNC = (V+ -6.5) to V+ (Note 7)
25
-
0.11
-
Ω
Full
-
0.14
-
Ω
NO or NC OFF Leakage Current, V+ = 5V, VCOM = -1.5V, 5V, VNO or VNC = 5V,
25
-
-8.13
-
nA
INO(OFF) or INC(OFF)
-1.5V
Full
-
-0.4
-
µA
COM ON Leakage Current,
V+ = 5V, VCOM = -1.5V, 5V, VNO or VNC = Float 25
-
-4.42
-
nA
ICOM(ON)
Full
-
-0.33
-
µA
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
V+ = 4.5V, VNO or VNC = 3.0V, RL = 50Ω,
25
-
35
-
ns
CL = 35pF (see Figure 1)
Full
-
50
-
ns
Turn-OFF Time, tOFF
V+ = 4.5V, VNO or VNC = 3.0V, RL = 50Ω,
25
-
16
-
ns
CL = 35pF (see Figure 1)
Full
-
22
-
ns
Break-Before-Make Time Delay, tD V+ = 5.5V, VNO or VNC = 3.0V, RL = 50Ω,
Full
-
18
-
ns
CL = 35pF (see Figure 3)
Charge Injection, Q
VG = 0V, RG = 0Ω, CL = 1.0nF (see Figure 2)
25
-
170
-
pC
OFF-Isolation
RL = 50Ω, CL = 5pF, f = 100kHz, VNO or
VNC = 1VRMS (see Figure 4)
25
-
60
-
dB
Crosstalk (Channel-to-Channel)
RL = 50Ω, CL = 5pF, f = 1MHz, VNO or
VNC = 1VRMS (See Figure 6)
25
-
-75
-
dB
Total Harmonic Distortion
f = 20Hz to 20kHz, VCOM = 0.5VP-P, RL = 32Ω
25
-
0.02
-
%
-3dB Bandwidth
VCOM = 1VRMS, RL = 50Ω, CL = 5pF
25
-
60
-
MHz
NOx or NCx OFF Capacitance,
f = 1MHz (see Figure 7)
25
-
36
-
pF
COFF
COMx ON Capacitance, CCOM(ON) f = 1MHz (see Figure 7)
25
-
88
-
pF
3
FN6583.2
November 3, 2009
 ▷