ISL54057 Datasheet, PDF (3/10 Pages) Intersil Corporation – Ultra Low ON-Resistance, Low-Voltage, Single Supply, Differential 4 to 1 Analog Multiplexer

ISL54057
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 4.7V
Input Voltages
INH, Ax, Bx, ADDx (Note 2) . . . . . . . . . . . . . . -0.3 to (V+) + 0.3V
Output Voltages
COMx (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to (V+) + 0.3V
Continuous Current NO or COM . . . . . . . . . . . . . . . . . . . . . ±300mA
Peak Current NO or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±500mA
ESD Rating
HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >4kV
MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >300V
CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >1kV
Thermal Information
Thermal Resistance (Typical, Note 3)
θ_JA (^oC/W)
µTQFN Package . . . . . . . . . . . . . . . . . . . . . . . . . . .
93
Maximum Junction Temperature (Plastic Package) . . . . . . +150°C
Maximum Storage Temperature Range. . . . . . . . . . . -65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . +300°C
(Lead Tips Only)
Operating Conditions
Temperature Range
ISL54057IRUZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. Signals on Ax, Bx, COMx, ADDx, or INH exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current
ratings.
3. θ_JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications: 3V Supply
Test Conditions: V_SUPPLY = +2.7V to +3.3V, GND = 0V, V_INH = 1.4V, V_INL = 0.5V
(Notes 4, 8), Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
ON Resistance, R_ON
V+ = 2.7V, I_COM = 100mA, V_{AX or} V_BX = 0V to V+
(See Figure )
R_ON Matching Between Channels, V+ = 2.7V, I_COM = 100mA, V_{AX or} V_BX = Voltage at
∆R_ON
max R_ON, Note 6
R_ON Flatness, R_FLAT(ON)
V+ = 2.7V, I_COM = 100mA, V_{AX or} V_BX = 0V t0 V+
(Note 7)
Ax or Bx OFF Leakage Current,
I_Ax(OFF) or I_Bx(OFF)
V+ = 3.3V, V_COM = 0.3V, 3V, V_{AX or} V_BX = 3V, 0.3V
COM ON Leakage Current,
I_COM(ON)
V+ = 3.3V, V_COM = V_{AX or} V_BX = 0.3V, 3V
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, V_INH, V_ADDH
Input Voltage Low, V_INL, V_ADDL
Input Current, I_INH, I_INL, I_ADDH,
I_ADDL
DYNAMIC CHARACTERISTICS
V+ = 3.3V, V_INH = V_ADD = 0V or V+
Inhibit Turn-ON Time, t_ON
V+ = 2.7V, V_{Ax or} V_Bx = 1.5V, R_L = 50Ω, C_L = 35pF
(See Figure 1)
Inhibit Turn-OFF Time, t_OFF
V+ = 2.7V, V_{Ax or} V_Bx = 1.5V, R_L = 50Ω, C_L = 35pF,
See Figure 1
Address Transition Time, t_TRANS V+ = 2.7V, V_{AX or} V_BX = 1.5V, R_L = 50Ω, C_L = 35pF
(See Figure 1)
Break-Before-Make Time, t_BBM
V+ = 3.3V, V_{AX or} V_BX = 1.5V, R_L = 50Ω, C_L = 35pF
(See Figure 2)
Ax or Bx OFF Capacitance, C_OFF
COM OFF Capacitance, C_OFF
COM ON Capacitance, C_COM(ON)
f = 1MHz, V_{AX or} V_BX = V_COM = 0V (See Figure )
f = 1MHz, V_{AX or} V_BX = V_COM = 0V (See Figure 6)
f = 1MHz, V_{AX or} V_BX = V_COM = 0V (See Figure 6)
TEMP (NOTE 5)
(°C)
MIN
Full
0
25
-
Full
-
25
-
Full
-
25
-
Full
-
25
-4
Full
-35
25
-8.5
Full
-60
Full
1.4
Full
-
Full
-0.5
25
-
Full
-
25
-
Full
-
25
-
Full
-
25
-
Full
-
25
-
25
-
25
-
TYP
-
0.43
-
0.09
-
0.07
-
-
-
-
-
-
-
-
27
37
18
28
29
40
4
1
44
149
201
(NOTE 5)
MAX UNITS
V+
V
0.75
Ω
0.8
Ω
0.2
Ω
0.2
Ω
0.15
Ω
0.15
Ω
4
nA
35
nA
8.5
nA
60
nA
-
V
0.5
V
0.5
µA
-
ns
-
ns
-
ns
-
ns
-
ns
-
ns
-
ns
-
ns
-
pF
-
pF
-
pF
3
FN6379.0
September 29, 2006