ISL45042_06 Datasheet, PDF (3/8 Pages) Intersil Corporation – LCD Module Calibrator

ISL45042
Absolute Maximum Ratings
V_DD to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+4V
Input Voltages to GND
SET, CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +4V
AVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +20V
CTL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +17V
Output Voltages to GND
OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +20V
ESD Rating
HBM for Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.75kV
HBM for CTL to GND (no EEPROM Content Disruption). . . . .8kV
Operating Conditions
Temperature Range
ISL45042IR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Thermal Information
Thermal Resistance (Typical, Note 1)
θ_JA (°C/W)
8 Ld Thin DFN Package. . . . . . . . . . . . . . . . . . . . . .
90
Moisture Sensitivity (see Technical Brief TB363)
All Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 1
Maximum Junction Temperature (Plastic Package) . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . +300°C
(Lead Tips Only)
Erase/Write Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10,000
Data Retention. . . . . . . . . . . . . . . . . . . . . . . . . . . 10 years @ +85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θ_JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379.
Electrical Specifications
PARAMETER
Test Conditions: VDD = 3V, AVDD = 10V, OUT = 5V, R_SET = 24.9kΩ; Unless Otherwise Specified.
Typicals are at T_A = +25°C
SYMBOL
TEST CONDITIONS
TEMP
(°C)
MIN
TYP MAX
UNITS
DC CHARACTERISTICS
V_DD Supply Range
V_DD
For Programming
For Operation
0 to 85
3
Full
2.6
-
3.6
V
-
3.6
V
V_DD Supply Current
I_DD
CE = V_DD (Note 6)
CE = GND
Full
-
Full
-
-
50
μA
-
20
μA
AVDD Supply Range
AVDD
Full
4.5
-
20
V
AVDD Supply Current
IAVDD
(Note 3)
Full
-
-
20
μA
CTL High Voltage
CTL Low Voltage
CTL High Rejected Pulse Width
CTL Low Rejected Pulse Width
CTL High Minimum Pulse Width
CTL Low Minimum Pulse Width
CTL Minimum Time Between
Counts
CTL_IH
CTL_IL
CTL_IHRPW
CTL_ILRPW
CTL_IHMPW
CTL_ILMPW
CTL_MTC
2.6V < V_DD < 3.6V
2.6V < V_DD < 3.6V
Full 0.7*V_DD
Full 0.2*V_DD
Full
20
Full
20
Full
-
Full
-
Full
-
-
0.8*V_DD V
-
0.3*V_DD V
-
-
μs
-
-
μs
-
200
μs
-
200
μs
-
10
μs
CTL Input Current
ICTL
CTL = GND
Full
-
-
10
μA
CTL Input Capacitance
CE Input Low Voltage
CE Input High Voltage
CE Minimum Start Up Time
CTL EEPROM Program Voltage
CTL EEPROM Programming
Signal Time
CTL_CAP
CE_IL
CE_IH
CE_ST
CTL_PROM
CTL_PT
CTL = V_DD
(Note 5)
2.6V < V_DD < 3.6V
2.6V < V_DD < 3.6V
(Note 5)
2.6V < V_DD < 3.6V, (Note 2)
>4.9V
Full
-
-
Full
-
10
Full
-
-
Full 0.64*V_DD
-
Full
-
1
Full
4.9
-
Full
200
-
10
μA
-
pF
0.4
V
-
V
-
ms
15.75 V
-
μs
3
FN6072.6
November 14, 2006