English
Language : 

ISL43L220 Datasheet, PDF (3/13 Pages) Intersil Corporation – Ultra Low ON-Resistance, Low Voltage,Single Supply, Dual SPDT Analog Switch
◁
ISL43L220
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 4.7V
Input Voltages
NO, NC, IN (Note 2) . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current NO, NC, or COM . . . . . . . . . . . . . . . . . ±300mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±500mA
ESD Rating:
HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>9kV
MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>500V
CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>1kV
Thermal Information
Thermal Resistance (Typical, Note 3)
θJA (°C/W)
10 Ld 3x3 DFN Package . . . . . . . . . . . . . . . . . . . . .
110
Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(Lead Tips Only)
Operating Conditions
Temperature Range
ISL43L220IR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. Signals on NC, NO, IN, or COM exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
3. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 4.3V Supply
Test Conditions: V+ = +3.9V to +4.5V, GND = 0V, VINH = 1.6V, VINL = 0.5V (Notes 4, 6),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(NOTE 5)
(°C)
MIN
TYP
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
Full
0
-
V+
V
ON Resistance, RON
V+ = 3.9V, ICOM = 100mA, VNO or VNC = 0V to V+
25
-
0.23
0.35
Ω
(See Figure 5)
Full
-
-
0.35
Ω
RON Matching Between Channels, V+ = 3.9V, ICOM = 100mA, VNO or VNC = Voltage at
25
-
0.03
0.06
Ω
∆RON
max RON (Note 9)
Full
-
-
0.06
Ω
RON Flatness, RFLAT(ON)
V+ = 3.9V, ICOM = 100mA, VNO or VNC = 0V to V+
25
-
0.03
0.08
Ω
(Note 7)
Full
-
-
0.08
Ω
NO or NC OFF Leakage Current, V+ = 4.5V, VCOM = 0.3V, 3V, VNO or VNC = 3V, 0.3V
25
-45
-
45
nA
INO(OFF) or INC(OFF)
Full
-110
-
110
nA
COM ON Leakage Current,
ICOM(ON)
V+ = 4.5V, VCOM = 0.3V, 3V, or VNO or VNC = 0.3V, 3V, 25
-45
-
45
nA
or Floating
Full
-100
-
100
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
V+ = 3.9V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF
25
-
(See Figure 1, Note 8)
Full
-
12
17
ns
-
22
ns
Turn-OFF Time, tOFF
V+ = 3.9V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF
25
-
(See Figure 1, Note 8)
Full
-
5
10
ns
-
15
ns
Break-Before-Make Time Delay, tD V+ = 4.5V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF Full
2
4
-
ns
(See Figure 3, Note 8)
Charge Injection, Q
OFF Isolation
CL = 1.0nF, VG = 0V, RG = 0Ω, (See Figure 2)
RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS
(See Figure 4)
25
-
128
-
pC
25
-
68
-
dB
Crosstalk (Channel-to-Channel)
RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS,
25
(See Figure 6)
Total Harmonic Distortion
f = 20Hz to 20kHz, VCOM = 2VP-P, RL = 600Ω
25
NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 7)
25
COM ON Capacitance, CCOM(ON) f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 7)
25
-
-95
-
dB
-
0.003
-
%
-
115
-
pF
-
224
-
pF
3
FN6093.2
April 12, 2005
 ▷