ISL43L120 Datasheet, PDF (3/11 Pages) Intersil Corporation – Ultra Low ON-Resistance, Single Supply, Dual SPST Analog Switches

ISL43L120, ISL43L121, ISL43L122
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 4.7V
Input Voltages
IN (Note 4). . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
NO, NC (Note 4) . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 4) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . 300mA
Peak Current, IN, NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . 500mA
ESD Rating (Per MIL-STD-883 Method 3015). . . . . . . . . . . . . .>8kV
Thermal Information
Thermal Resistance (Typical, Note 5)
θ_JA (°C/W)
8 Ld 3x3 DFN Package . . . . . . . . . . . . . . . . . . . . . .
110
8 Ld MSOP Package . . . . . . . . . . . . . . . . . . . . . . . .
190
Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(Lead Tips Only)
Operating Conditions
Temperature Range
ISL43L12XIU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
4. Signals on NC, NO, COM, or IN exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
5. θ_JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 3V Supply Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, V_INH = 1.4V, V_INL = 0.5V (Note 6, 8),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP MIN
MAX
(°C) (NOTE 7) TYP (NOTE 7) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
Full
0
-
V+
V
ON Resistance, R_ON
V+ = 2.7V, I_COM = 100mA, V_NO or V_NC = 0V to V+
25
-
0.17
0.25
Ω
See Figure 4
Full
-
-
0.3
Ω
R_ON Matching Between Channels, V+ = 2.7V, I_COM = 100mA, V_NO or V_NC = Voltage at
25
-
0.005
0.02
Ω
∆R_ON
Max R_ON, Note 10
Full
-
-
0.04
Ω
R_ON Flatness, R_Flat(ON)
V+ = 2.7V, I_COM = 100mA, V_NO or V_NC = 0V to V+,
25
-
0.008
0.06
Ω
Note 11
Full
-
-
0.07
Ω
NO or NC OFF Leakage Current, V+ = 3.3V, V_COM = 0.3, 3V, V_NO or V_NC = 3V, 0.3V
25
-3
-
3
nA
I_NO(OFF) or I_NC(OFF)
Full
-60
-
60
nA
COM ON Leakage Current,
I_COM(ON)
V+ = 3.3V, V_COM = 0.3V, 3V, or V_NO or V_NC = 0.3V, 3V 25
-3
-
Full
-80
-
3
nA
80
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, t_ON
V+ = 2.7V, V_NO or V_NC = 1.5V, R_L = 50Ω, C_L = 35pF,
25
-
V_IN = 0 to 2.7V, See Figure 1, Note 9
Full
-
15
25
ns
-
30
ns
Turn-OFF Time, t_OFF
V+ = 2.7V, V_NO or V_NC = 1.5V, R_L = 50Ω, C_L = 35pF,
25
-
V_IN = 0 to 2.7V, See Figure 1, Note 9
Full
-
15
25
ns
-
30
ns
Charge Injection, Q
OFF Isolation
C_L = 1.0nF, V_G = 0V, R_G = 0Ω, See Figure 2
25
-
-125
-
pC
R_L = 50Ω, C_L = 5pF, f = 100kHz, V_COM = 1 V_RMS, See 25
-
62
-
dB
Figure 3
Crosstalk (Channel-to-Channel)
R_L = 50Ω, C_L = 5pF, f = 100kHz, V_COM = 1 V_RMS, See
25
-
-94
-
dB
Figure 5
NO or NC OFF Capacitance, C_OFF f = 1MHz, V_NO or V_NC = V_COM = 0V, See Figure 6
25
-
182
-
pF
3
FN6091.1
November 3, 2004