 English |
|
|
|
|
|
|
|
| ISL43L110_15 Datasheet, PDF (3/12 Pages) Intersil Corporation – Ultra Low ON-Resistance, +1.1V to +4.5V Single Supply, SPST Analog Switches | |||
| |||
| ◁ |
ISL43L110, ISL43L111
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 4.7V
Input Voltages
NO, NC, IN (Note 2) . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current NO, NC, or COM . . . . . . . . . . . . . . . . . ï±300mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) ï ï®ï ï®ï ï®ï ï®ï ï®ï ï®ï ï®ï ï®ï ï®ï ï®ï ï®ï ï®ï ï®ï ï®ï ï®ï ï®ï ï®ï ï± 600mA
ESD Rating:
HBM ï¾ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>4kV
MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>300V
CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>1000V
Thermal Information
Thermal Resistance (Typical, Note 3)
ï±JA (°C/W)
5 Ld SC70 Package . . . . . . . . . . . . . . . . . . . . . . . . .
660
Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(Lead Tips Only)
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
CAUTION: Stresses above those listed in âAbsolute Maximum Ratingsâ may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. Signals on NC, NO, IN, or COM exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
3. ï±JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 4.3V Supply
Test Conditions: V+ = +3.9V to +4.5V, GND = 0V, VINH = 1.6V, VINL = 0.5V (Notes 4, 6),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
ON Resistance, RON
V+ = 3.9V, ICOM = 100mA, VNO or VNC = 2.2V
(See Figure 4)
RON Flatness, RFLAT(ON)
V+ = 3.9V, ICOM = 100mA, VNO or VNC = 0.8V, 2.2V,
3.5V, (Note 7)
NO or NC OFF Leakage Current,
INO(OFF) or INC(OFF)
COM ON Leakage Current,
ICOM(ON)
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
V+ = 4.5V, VCOM = 0.3V, 3V, VNO or VNC = 3V, 0.3V
Vï« = 4.5V, VCOM = 0.3V, 3V, or VNO or VNC = 0.3V, 3V,
or Floating
V+ = 3.9V, VNO or VNC = 1.5V, RL = 50ï, CL = 35pF
(See Figure 1, Note 8)
Turn-OFF Time, tOFF
V+ = 3.9V, VNO or VNC = 1.5V, RL = 50ï, CL = 35pF
(See Figure 1, Note 8)
Charge Injection, Q
OFF Isolation
VG = V+/2, RG = 0ïï¬ï CL = 1.0nF (See Figure 2)
RL = 50ï, CL = 5pF, f = 100kHz, VCOM = 1VRMS,
(See Figure 3)
Total Harmonic Distortion
f = 20Hz to 20kHz, VCOM = 2VP-P, RL = 32ï
NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 5)
COM ON Capacitance, CCOM(ON) f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 5)
TEMP (NOTE 5)
(°C)
MIN
Full
0
25
-
Full
-
25
-
Full
-
25
-30
Full
-200
25
-3
Full
-35
25
-
Full
-
25
-
Full
-
25
-
25
-
25
-
25
-
25
-
TYP
-
0.22
0.25
0.03
0.05
-
-
-
-
8
-
5
-
89
-65
0.003
68
160
(NOTE 5)
MAX UNITS
V+
V
-
ï
-
ï
-
ï
-
ï
30
nA
200
nA
3
nA
35
nA
15
ns
20
ns
10
ns
15
ns
-
pC
-
dB
-
%
-
pF
-
pF
3
FN6130.1
August 24, 2015
|
▷ |
German
Russian
Spanish
Italian
Polish
Chinese
Japanese
Korean
French
Portuguese