ISL43841 Datasheet, PDF (3/14 Pages) Intersil Corporation – Low-Voltage, Single and Dual Supply, Dual 4 to 1 Multiplexer Analog Switch with Latch

ISL43841
Absolute Maximum Ratings
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V
V- to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -15 to 0.3V
Input Voltages
LATCH, NO, ADD (Note 1) . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . ±30mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±100mA
Thermal Information
Thermal Resistance (Typical, Note 2)
θ_JA (^oC/W)
20 Ld 4x4 QFN Package . . . . . . . . . . . . . . . . . . . . .
45
Maximum Junction Temperature (Plastic Package) . . . . . . . 150^oC
Maximum Storage Temperature Range. . . . . . . . . . . . -65^oC to 150^oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300^oC
(Lead Tips Only)
Operating Conditions
Temperature Range
ISL43841IR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40^oC to 85^oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Signals on NO, COM, ADD, or LATCH exceeding V+ or V- are clamped by internal diodes. Limit forward diode current to maximum current
ratings.
2. θ_JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications: ±5V Supply Test Conditions: V_SUPPLY = ±4.5V to ±5.5V, GND = 0V, V_INH = 2.4V, V_INL = 0.8V (Note 3),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 4)
(NOTE 4)
(^oC)
MIN
TYP
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
ON Resistance, R_ON
V_S = ±4.5V, I_COM = 2mA, V_NO = 3V,
(See Figure 6)
Full
V-
-
V+
V
25
-
44
50
Ω
Full
-
-
80
Ω
R_ON Matching Between Channels, V_S = ±4.5V, I_COM = 2mA, V_NO = 3V, (Note 5)
∆R_ON
25
-
1.3
4
Ω
Full
-
-
6
Ω
R_ON Flatness, R_FLAT(ON)
V_S = ±4.5V, I_COM = 2mA, V_NO = ±3V, 0V,
(Note 6)
25
-
Full
-
7.5
9
Ω
-
12
Ω
NO or NC OFF Leakage Current,
I_NO(OFF) or I_NC(OFF)
V_S = ±5.5V, V_COM = ±4.5V, V_NO = +4.5V, (Note 7)
25
-0.1
0.002
0.1
nA
Full
-2.5
-
2.5
nA
COM OFF Leakage Current,
I_COM(OFF)
V_S = ±5.5V, V_COM = ±4.5V, V_NO = +4.5V, (Note 7)
25
-0.1
0.002
0.1
nA
Full
-2.5
-
2.5
nA
COM ON Leakage Current,
I_COM(ON)
V_S = ±5.5V, V_COM = V_NO = ±4.5V, (Note 7)
25
-0.1
0.002
0.1
nA
Full
-2.5
-
2.5
nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, V_LATCHH,
V_ADDH
Input Voltage Low, V_LATCHL,
V_ADDL
Input Current, _LATCHH, _LATCHL,
I_ADDH, I_ADDL
DYNAMIC CHARACTERISTICS
V_S = ±5.5V, V_LATCHH, V_ADD = 0V or V+
Full
2.4
-
Full
-
-
Full
-0.5
0.03
-
V
0.8
V
0.5
µA
Address Transition Time, t_TRANS
V_S = ±4.5V, V_NO = ±3V, R_L = 300Ω, C_L = 35pF,
V_IN = 0 to 3, (See Figure 1)
25
-
Full
-
43
60
ns
-
70
ns
Break-Before-Make Time, t_BBM
V_S = ±5.5V, V_NO = 3V, R_L = 300Ω, C_L = 35pF,
V_IN = 0 to 3V, (See Figure 3)
Full
2
7
-
ns
3