English
Language : 

ISL43410_14 Datasheet, PDF (3/13 Pages) Intersil Corporation – Low-Voltage, Single Supply, DPDT High Performance Analog Switch
◁
ISL43410
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 15V
Input Voltages
INH, NO, NC, ADD (Note 2) . . . . . . . . . . . . -0.3V to ((V+) + 0.3V)
Output Voltages
COM (Note 2) . . . . . . . . . . . . . . . . . . . . . . . -0.3V to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . 40mA
Operating Conditions
Temperature Range
ISL43410Ix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
Thermal Information
Thermal Resistance (Typical)
θJA (°C/W) θJC (°C/W)
10 Ld MSOP Package (Note 3) . . . . . . 190
N/A
16 Ld QFN Package (Notes 4, 5). . . . .
58
11
Maximum Junction Temperature (Plastic Package). . . . . . . +150°C
Moisture Sensitivity (See Technical Brief TB363)
All Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 1
Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
2. Signals on NC, NO, COM, ADD, or INH exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current
ratings.
3. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
4. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
5. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications +5V Supply Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 6), Unless
Otherwise Specified.
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 7, 12) TYP (Notes 7, 12) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
ON-Resistance, rON
V+ = 4.5V, ICOM = 1.0mA, VNO or VNC = 3.5V,
(See Figure 5, Note 11)
Full
0
25
-
Full
-
-
V+
V
115
125
Ω
-
150
Ω
rON Matching Between Channels, V+ = 4.5V, ICOM = 1.0mA, VNO or VNC = 3.5V,
25
-
1
3
Ω
ΔrON
(Notes 9, 11)
Full
-
-
5
Ω
rON Flatness, rFLAT(ON)
V+ = 5.5V, ICOM = 1.0mA, VNO or VNC = 1.5V, 2.5V, 25
-
12
13
Ω
3.5V, (Notes 10, 11)
Full
-
13
18
Ω
NO or NC OFF Leakage Current, V+ = 5.5V, VCOM = 1V, 4.5V, VNO or VNC = 4.5V, 1V
25
-3
-
3
nA
INO(OFF) or INC(OFF)
(Note 8)
Full
-5
-
5
nA
COM OFF Leakage Current,
V+ = 5.5V, VCOM = 4.5V, 1V, VNO or VNC = 1V, 4.5V
25
-3
-
3
nA
ICOM(OFF)
(Note 8)
Full
-5
-
5
nA
COM ON Leakage Current,
V+ = 5.5V, VCOM = 1V, 4.5V, or VNO or VNC = 1V, 4.5V, 25
-3
-
3
nA
ICOM(ON)
or Floating (Note 8)
Full
-5
-
5
nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, VINH
Input Voltage Low, VINL
Input Current, IINH, IINL
DYNAMIC CHARACTERISTICS
V+ = 5.5V, VIN = 0V or V+
Full
2.4
1.4
-
V
Full
-
1.3
0.8
V
Full
-0.5
-
0.5
µA
Inhibit Turn-ON Time, tON
V+ = 4.5V, VNO or VNC = 3V, RL = 300Ω, CL = 35pF, 25
-
60
-
ns
VIN = 0 to 3 (See Figure 1)
Full
-
75
-
ns
3
FN6044.4
May 12, 2008
 ▷