ISL43210A_14 Datasheet, PDF (3/12 Pages) Intersil Corporation – Medium-Voltage, Single Supply, Single SPDT Analog Switch

ISL43210A
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 16.5V
Input Voltages
IN (Note 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
NO, NC (Note 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . . . . . . . . 40mA
ESD Rating
Human Body Model (Tested per JESD22-A114E) . . . . . . . . . . . . . . . . 2kV
Machine Model (Tested per JESD22-A115-A) . . . . . . . . . . . . . . . . . 100V
Latch Up (Tested per JESD-78B; Class 2, Level A) . . . . . . . . . . . . . . 100mA
Thermal Information
Thermal Resistance (Typical)
θ_JA (°C/W) θ_JC (°C/W)
6 Ld SOT-23 Package (Notes 7, 8) . . . . . . . 175
95
Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . +150°C
Maximum Storage Temperature Range. . . . . . . . . . . . . . . . . -65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Maximum Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
6. Signals on NC, NO, COM, or IN exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
7. θ_JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
8. For θ_JC, the “case temp” location is taken at the package top center.
Electrical Specifications - 12V Supply Test Conditions: V+ = +10.8V to +15V, GND = 0V, V_INH = 4V, V_INL = 0.8V (Note 9),
Unless Otherwise Specified. Boldface limits apply over the operating temperature range, -40°C to +85°C.
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 10, 11) TYP (Notes 10, 11) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
Full
0
-
V+
V
ON-Resistance, r_ON
V+ = 10.8V, I_COM = 1.0mA, V_NO or V_NC = 10V
25
-
11
20
Ω
(see Figure 5)
Full
-
15
25
Ω
r_ON Matching Between Channels, Δr_ON V+ = 10.8V, I_COM = 1.0mA, V_NO or V_NC = 10V
25
-
0.8
2
Ω
Full
-
1
4
Ω
r_ON Flatness, R_FLAT(ON)
V+ = 10.8V, I_COM = 1.0mA, V_NO or V_NC = 3V, 6V, 9V 25
-
1
4
Ω
(Note 12)
Full
-
-
6
Ω
NO or NC OFF Leakage Current, I_NO(OFF) V+ = 15V, V_COM = 1V, 12V, V_NO or V_NC = 12V, 1V
25
-3
0.01
3
nA
or I_NC(OFF)
Full
-5
-
5
nA
COM OFF Leakage Current, I_COM(OFF) V+ = 15V, V_COM = 12V, 1V, V_NO or V_NC = 1V, 12V
25
-3
0.01
3
nA
Full
-5
-
5
nA
COM ON Leakage Current, I_COM(ON)
V+ = 15V, V_COM = 1V, 12V, or V_NO or V_NC = 1V, 12V or 25
-5
-
5
nA
floating
Full
-10
-
10
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, t_ON
V_NO or V_NC = 10V, R_L = 1kΩ, C_L = 35pF, V_IN = 0V to 25
-
25
-
ns
4V
(see Figure 1)
Full
-
35
-
ns
Turn-OFF Time, t_OFF
V_NO or V_NC = 10V, R_L = 1kΩ, C_L = 35pF, V_IN = 0V to 4V 25
-
17
-
ns
(see Figure 1)
Full
-
26
-
ns
Break-Before-Make Time Delay, t_D
Charge Injection, Q
OFF Isolation
R_L = 300Ω, C_L = 35pF, V_NO or V_NC = 10V,
V_IN = 0V to 4V (see Figure 3)
C_L = 1.0nF, V_G = 0V, R_G = 0Ω (see Figure 2)
R_L = 50Ω, C_L = 5pF, f = 1MHz (see Figure 4)
Full
-
2
-
ns
25
-
5
-
pC
25
-
76
-
dB
3
FN7876.0
June 24, 2011