ISL28915_14 Datasheet, PDF (3/10 Pages) Intersil Corporation – Nano Power, Push/Pull Output Comparator

ISL28915
Absolute Maximum Ratings
Maximum Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.75V
Supply Turn-On Voltage Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/µs
Maximum Differential Input Current . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
Maximum Differential Input Voltage . . . . . . . . . . . GND - 0.5V to V+ + 0.5V
Min/Max Input Voltage . . . . . . . . . . . . . . . . . . . . . . GND - 0.5V to V+ + 0.5V
Output Short-Circuit Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite
ESD Tolerance
Human Body Model (Tested per JESD22-A114F) . . . . . . . . . . . . . . . . 3kV
Machine Model (Tested per JESD22-A115-C) . . . . . . . . . . . . . . . . . . 150V
Charged Device Model (Tested per JESD22-C110D) . . . . . . . . . . . . . 1kV
Latch-up (Tested per JESD-78B; Class 2, Level A) . . . . . . . . . . . . . . . at +125°C
Thermal Information
Thermal Resistance (Typical)
θ_JA (°C/W) θ_JC (°C/W)
6 Ld SOT-23 Package (Notes 4, 5) . . . . . . . 239
108
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Recommended Operating Conditions
Ambient Temperature Range (T_A) . . . . . . . . . . . . . . . . . . .-40°C to +125°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .+125°C
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8V to 5.5V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. θ_JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
5. For θ_JC, the “case temp” location is taken at the package top center.
Electrical Specifications V+ = 5V, GND = 0V, V_CM = 2.5V, T_A = +25°C, unless otherwise specified. Boldface limits apply over
-40°C to +125°C.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
MAX
(Note 6) TYP (Note 6) UNIT
V_OS
Input Offset Voltage
-2
-0.2
2
mV
-2.5
2.5
mV
I_OS
Input Offset Current
-25
-3
25
pA
-67
67
pA
I_B
Input Bias Current
-31
1.2
31
pA
-100
100
pA
CMIR
Common Mode Input Range
Established by CMRR test
0
5
V
CMRR
Common-Mode Rejection Ratio
V_CM = 0.5V to 3.5V
72
98
dB
70
dB
PSRR
Power Supply Rejection Ratio
V_CM = 0V to 5V
V+ = 1.8V to 5.5V
60
dB
77
100
dB
70
dB
V_OUT
I_S,ON
Maximum Output Voltage Swing
R_L terminated to V+/2
Supply Current, Enabled
Output low, R_L = 10kΩ
Output high, R_L = 10kΩ
V_EN = V+ - 0.3V
35
70
mV
4.930 4.990
V
500
600
nA
900
nA
I_S,OFF
Supply Current, Disabled
V_EN = GND + 0.3V
0.25
20
nA
50
nA
V_SUPPLY
Supply Voltage Range
C_IN
Input Capacitance
ENABLE INPUT
1.8
5.5
V
6
pF
V_ENH
V_ENL
I_EN-H,L
Enable Pin High Level
Enable Pin Low Level
Enable Pin Input Current
V_EN = 0V, 5V
V+ - 0.3
-80
-200
V
GND + 0.3 V
2.2
80
nA
200
nA
3
July 12, 2012
FN8343.0