English
Language : 

ISL28136 Datasheet, PDF (3/14 Pages) Intersil Corporation – 5MHz, Single Precision Rail-to-Rail Input-Output RRIO Op Amp
◁
ISL28136
Electrical Specifications
V+ = 5V, V- = 0V, VCM = 2.5V, RL = Open, TA = +25°C unless otherwise specified.
Boldface limits apply over the operating temperature range, -40°C to +125°C. Temperature data
established by characterization. (Continued)
PARAMETER
DESCRIPTION
CONDITIONS
MIN
MAX
(Note 1) TYP (Note 1) UNIT
IO-
Short-Circuit Output Sink Current
RL = 10Ω to VCM
50
55
mA
45
VSUPPLY
VENH
VENL
IENH
Supply Operating Range
EN Pin High Level
EN Pin Low Level
EN Pin Input High Current
V+ to V-
VEN = V+
2.4
5.5
V
2
V
0.8
V
1
1.5
µA
1.6
IENL
EN Pin Input Low Current
VEN = V-
16
25
nA
30
AC SPECIFICATIONS
GBW
Unity Gain
Bandwidth
eN
iN
CMRR
Gain Bandwidth Product
-3dB Bandwidth
Input Noise Voltage Peak-to-Peak
Input Noise Voltage Density
Input Noise Current Density
Input Common Mode Rejection Ratio
PSRR+
to 120Hz
Power Supply Rejection Ratio (V+)
PSRR-
to 120Hz
Power Supply Rejection Ratio (V-)
TRANSIENT RESPONSE
AV = 100, RF = 100kΩ, RG = 1kΩ to VCM
AV = 1, RF = 0Ω, RL = 10kΩ to VCM,
VOUT = 10mVP-P
f = 0.1Hz to 10Hz, RL = 10kΩ to VCM
fO = 1kHz, RL = 10kΩ to VCM
fO = 10kHz, RL = 10kΩ to VCM
fO = to 120Hz; VCM = 1VP-P, RL = 1kΩ to
VCM
V+, V- = ±1.2V and ±2.5V,
VSOURCE = 1VP-P, RL = 1kΩ to VCM
V+, V- = ±1.2V and ±2.5V
VSOURCE = 1VP-P, RL = 1kΩ to VCM
5
13
0.4
15
0.35
-90
-88
-105
MHz
MHz
µVP-P
nV/√Hz
pA/√Hz
dB
dB
dB
SR
Slew Rate
VOUT = ±1.5V; Rf = 50kΩ, RG = 50kΩ to
VCM
±1.9
V/µs
tr, tf, Large
Rise Time, 10% to 90%, VOUT
AV = +2, VOUT = 2VP-P, Rg = Rf = RL = 1kΩ
0.6
µs
Signal
to VCM
Fall Time, 90% to 10%, VOUT
AV = +2, VOUT = 2VP-P, Rg = Rf = RL = 1kΩ
0.5
µs
to VCM
tr, tf, Small
Signal
Rise Time, 10% to 90%, VOUT
AV = +2, VOUT = 10mVP-P,
Rg = Rf = RL = 1kΩ to VCM
65
ns
Fall Time, 90% to 10%, VOUT
AV = +2, VOUT = 10mVP-P,
Rg = Rf = RL = 1kΩ to VCM
62
ns
tEN
Enable to Output Turn-on Delay Time, 10% VEN = 5V to 0V, AV = +2,
EN to 10% VOUT
Rg = Rf = RL = 1kΩ to VCM
5
µs
Enable to Output Turn-off Delay Time, 10% VEN = 0V to 5V, AV = +2,
EN to 10% VOUT
Rg = Rf = RL = 1kΩ to VCM
0.3
µs
NOTE:
1. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
3
FN6153.4
June 26, 2009
 ▷