ICL7663S_05 Datasheet, PDF (3/8 Pages) Intersil Corporation – CMOS Programmable Micropower Positive Voltage Regulator

ICL7663S
Absolute Maximum Ratings
Input Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+18V
Any Input or Output Voltage (Note 1)
Terminals 1, 2, 3, 5, 6, 7 . . . . . . . . . . . . . V_IN+ 0.3V to GND -0.3V
Output Source Current
Terminal 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA
Terminal 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25mA
Output Sinking Current
Terminal 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10mA
Operating Conditions
Temperature Range
ICL7663SC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
ICL7663SI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-25°C to 85°C
Thermal Information
Thermal Resistance (Typical, Note 2)
θ_JA (°C/W) θ_JC (°C/W)
CERDIP Package. . . . . . . . . . . . . . . . . 115
30
PDIP Package* . . . . . . . . . . . . . . . . . . 150
N/A
Plastic SOIC Package . . . . . . . . . . . . . 180
N/A
Maximum Junction Temperature
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
CERDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175°C
Maximum Storage Temperature Range . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C
(SOIC - Lead Tips Only)
*Pb-free PDIPs can be used for through hole wave solder processing
only. They are not intended for use in Reflow solder processing
applications.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Connecting any terminal to voltages greater than (V+_IN + 0.3V) or less than (GND - 0.3V) may cause destructive device latch-up. It is
recommended that no inputs from sources operating on external power supplies be applied prior to ICL7663S power-up.
2. θ_JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications Specifications Below Applicable to Both ICL7663S and ICL7663SA, Unless Otherwise Specified. V+_IN = 9V,
V_OUT = 5V, T_A = 25°C, Unless Otherwise Specified. Notes 4, 5. See Test Circuit, Figure 7
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX UNITS
Input Voltage
Quiescent Current
Reference Voltage
Temperature
Coefficient
Line Regulation
V_SET Input Current
Shutdown Input Current
Shutdown Input Voltage
Sense Pin Input Current
V+_IN
ICL7663S
T_A = 25°C
0°C < T_A < 70°C
-25°C < T_A < 85°C
ICL7663SA
0°C < T_A < 70°C
-25°C < T_A < 85°C
I_Q
1.4V ≤ V_OUT ≤ 8.5V, No Load
V+_IN = 9V
0°C < T_A < 70°C
-25°C < T_A < 85°C
V+_IN = 16V
0°C < T_A < 70°C
-25°C < T_A < 85°C
V_SET
I_OUT1 = 100µA, V_OUT = V_SET
ICL7663S
T_A = 25°C
ICL7663SA
T_A = 25°C
∆V_SET 0°C < T_A < 70°C
∆T
-25°C < T_A < 85°C
∆V_SET 2V < V_IN < 15V
0°C < T_A < 70°C
V_SET’ ∆V_IN
-25°C < T_A < 85°C
I_SET
0°C < T_A < 70°C
-25°C < T_A < 85°C
I_SHDN
V_SHDN V_SHDN HI: Both V_OUT Disabled
V_SHDN LO: Both V_OUT Enable
I_SENSE
1.5
-
16
V
1.6
-
16
V
1.6
-
16
V
1.6
-
16
V
1.6
-
16
V
-
-
10
µA
-
-
10
µA
-
-
12
µA
-
-
12
µA
1.2
1.3
1.4
V
1.275 1.29 1.305
V
-
100
-
ppm
-
100
-
ppm
-
0.03
-
%/V
-
0.03
0.3
%/V
-
0.01
10
nA
-
0.01
10
nA
-
±0.01
10
nA
1.4
-
-
V
-
-
0.3
V
-
0.01
10
nA
3
FN3180.5
July 21, 2005