HIP7038A8 Datasheet, PDF (3/5 Pages) Intersil Corporation – J1850 8-Bit 68HC05 Microcontroller 8K EEPROM Version

Specifications HIP7038A8
Absolute Maximum Ratings
Thermal Information
Supply Voltage (V_DD) . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6.0V
Input or Output Voltage
Pins with V_DD Diode . . . . . . . . . . . . . . . . . . . . -0.3V to V_DD +0.3V
Pins without V_DD Diode. . . . . . . . . . . . . . . . . . . . . -0.3V to +10.0V
Current Drain Per Pin, I (Excluding V_DD and V_SS) . . . . . . . . 25mA
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 2
Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21000 Gates
Operating Temperature Range (T_A) . . . . . . . . . . . . -40^oC to +125^oC
Storage Temperature Range (T_STG) . . . . . . . . . . . . -65^oC to +150^oC
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150^oC
Lead Temperature (During Soldering) . . . . . . . . . . . . . . . . +265^oC
1/16in. ± 1/32in. (1.59 ± 0.79mm) from case for 10s Max.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V
Operating Temperature Range . . . . . . . . . . . . . . . . . -40^oC to +85^oC
Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to +0.8V
Input High Voltage. . . . . . . . . . . . . . . . . . . . . . . . . .(0.8•V_DD) to V_DD
Input Rise and Fall Time
CMOS Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100ns Max.
CMOS Schmitt Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . .Unlimited
DC Electrical Specifications V_DD = 5V_DC ±10%, V_SS = 0V_DC, T_A = -40^oC to +85^oC Unless Otherwise Specified.
PARAMETERS
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SUPPLY CURRENT
RUN
WAIT
STOP
Powerdown Input Voltage:
RESET, IRQ, VPWIN, OSCIN
I_RUN
I_WAIT
I_STOP
V_INPD
T_A = +25^oC
T_A = -40^oC to +85^oC
V_DD = 0
-
50
-
mA
-
4
-
mA
-
100
-
µA
-
100
-
µA
-0.3
-
9
V
NOTE:
1. This device contains circuitry to protect the inputs against damage due to high static voltages of electric fields; however, it is advised that
normal precautions be taken to avoid application of any voltage higher than maximum rated voltages to this high impedance circuit. For
proper operation it is recommended that V_IN and V_OUT be constrained to the range V_SS<(V_IN or V_OUT)<V_DD. Reliability of operation is
enhanced if unused inputs except OSC2 are connected to an appropriate logic voltage level (e.g., either V_SS or V_DD).
9-101