HIP0045 Datasheet, PDF (3/10 Pages) Intersil Corporation – 1A/50V Octal Low Side Power Driver With Serial Bus Control and Fault Protection

HIP0045
Absolute Maximum Ratings
Maximum Output Voltage, V_OUT . . . . . . . . . . . . . . . . . . .-0.7 to V_OC
Peak Output Load Current, I_LOAD . . . . . As Specified for I_SC, I_LIM
Continuous Output Load Current, I_OUT (All 8 Outputs ON) . . . . 0.5A
Continuous Output Load Current, I_OUT (Any one Output ON) . . 1A
Total Average Current, I_OUT (All 8 Outputs) . . . . . . . . . . . . . . . 4.5A
Reverse Peak Current Drive, Any one Output, I_RD; t ≤ 2ms . . . -3A
DC Logic Supply, V_CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 7V
Input Voltage, All Inputs and Data Lines . . . . . . . -0.3 to V_CC +0.3V
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40^oC to 125^oC
Logic Supply Voltage, V_CC . . . . . . . . . . . . . . . . . . . . . 4.5V to 5.5V
Thermal Information
Thermal Resistance (Typical, Note 6)
θ_JA (^oC/W) θ_JC (^oC/W)
PSOP Package . . . . . . . . . . . . . . . . . .
40
2
Maximum Junction Temperature, T_J . . . . . . . . . . . . . . . . . . . .150^oC
Maximum
Maximum
Storage Temperature Range,
Lead Temperature (Soldering
T_STG
10s) .
.
.
.
.
.
.
.
.
-55^oC to 150^oC
. . . . . . . .265^oC
Die Characteristics
Back Side Potential . . . . . . . . . . . . . . . . . . .V- (GND Pin, Heat Sink)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
6. θ_JA Rated with standard PC Board, θ_JC rated with infinite heat sink.
Electrical Specifications V_CC = 4.5V to 5.5V, T_A = -40^oC to 125^oC, Unless Otherwise Specified
PARAMETER
SYMBOL
TEST CONDITIONS
MIN TYP MAX UNITS
Standby Current, No Load
Supply Current, Full Load
Output Clamping Voltage (Note 7)
Output Clamping Energy
I_CCO
I_CC
V_OC
E_OC
No Load
All Outputs ON, 0.5A Load Per Output
I_LOAD = 0.5A, Output Programmed OFF
1ms Single Pulse Width, T_A = 25^oC,
(Refer to Figure 4 for SOA)
-
-
5
mA
-
-
5
mA
45
-
62
V
20
45
-
mJ
Output Leakage Current 1 (Note 8)
I_{O LEAK1} V_OUT = 25V, Outputs OFF
-
Output Leakage Current 2 (Note 8)
I_{O LEAK2} V_OUT = 16V, Outputs OFF
-
Output Leakage Current 3 (Note 8)
I_{O LEAK3} V_OUT = 16V, Outputs OFF, V_CC = 1V
-
Drain-to-Source On Resistance, OUT0 - 7
r_DSON I_LOAD = 0.5A; T_J = 150^oC
-
Output Capacitance
C_OUT V_OUT = 16V, f = 1MHz
-
Turn-On Delay, OUT0, 1
t_d(ON) R_L = 500Ω, V_CE = 50% to V_OUT = 0.9 x V_BATT,
-
V_IN0,1 = 50% to V_OUT = 0.9 x V_BATT,
V_BATT = 16V
Turn-On Delay, OUT2 - 7
t_d(ON) R_L = 500Ω, V_CE = 50% to V_OUT = 0.9 x V_BATT,
-
V_BATT = 16V
Turn-Off Delay
t_d(OFF) R_L = 500Ω, V_CE = 50% to V_OUT = 0.1 x V_BATT,
-
V_IN0,1 = 50% to V_OUT = 0.9 x V_BATT,
V_BATT = 16V
Turn-On Voltage Slew-Rate, OUT2 - 7
-^d---^V----_d-^O--_t--^N----¹--
For V_OUT = 90% to 30% of V_BATT; V_BATT = 16V,
R_L = 500Ω
-
Turn-On Voltage Slew-Rate, OUT0, 1
Turn-Off Voltage Slew-Rate, OUT0 - 7
d_----V_{----d-O--t--N----2--}
For V_OUT = 90% to 30% of V_BATT; V_BATT = 16V,
R_L = 500Ω
-
-^d---^V-----^O----^F----^F---¹--
dt
For V_OUT = 30% to 90% of V_BATT; V_BATT = 16V,
R_L = 500Ω
-
Turn-Off Voltage Slew-Rate, OUT0 - 7
d_----V_{-----Od----tF----F---2--}
For V_OUT = 30% to 80% of V_OC;
V_BATT = 0.9 x V_OC, R_L = 500Ω
-
FAULT PARAMETERS
-
100
µA
-
100
µA
-
10
µA
-
1.5
Ω
-
20
pF
-
5
µs
-
10
µs
-
10
µs
0.7
3.5
V/µs
2
10
V/µs
2
10
V/µs
2
15
V/µs
Reverse Current Drive, OUT0 - 7
Reverse Voltage Drop, OUT0 - 7
∆I_CC during Reverse Current Drive
I_RD
V_RD
∆I_CC
I_OUT = -3A, t ≤2ms
I_OUT = -3A, t ≤2ms
-500
-
-
mA
-1.5
-
-
V
-
-
100
mA
4-3