English
Language : 

DG403DYZ-T Datasheet, PDF (3/12 Pages) Intersil Corporation – Monolithic CMOS Analog Switches
◁
Absolute Maximum Ratings
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.0V
GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V
VL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (GND - 0.3V) to (V+) +0.3V
Digital Inputs VS, VD (Note 1) . . . . . (V-) -2V to (V+) + 2V or 30mA,
Whichever Occurs First
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle, Max) . . 100mA
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20V (Max)
Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8V (Max)
Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4V (Min)
Input Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≤20ns
Thermal Information
Thermal Resistance (Typical, Note 2)
θJA (°C/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
115
TSSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . .
150
Maximum Junction Temperature (Plastic Package). . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . . -65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . +300°C
(SOIC and TSSOP- Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Signals on SX, DX, or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings.
2. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications Test Conditions: V+ = +15V, V- = -15V, VIN = 2.4V, 0.8V (Note 3), VL = 5V,
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 4) (NOTE 5) (NOTE 4)
(°C)
MIN
TYP
MAX UNITS
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
Turn-OFF Time, tOFF
Break-Before-Make Time Delay (DG403), tD
Charge Injection, Q (Figure 3)
OFF Isolation (Figure 4)
Crosstalk (Channel-to-Channel) (Figure 6)
RL = 300Ω, CL = 35pF
RL = 300Ω, CL = 35pF
CL = 10nF, VG = 0V, RG = 0Ω
RL = 100Ω, CL = 5pF, f = 1MHz
+25
-
+25
-
+25
5
+25
-
+25
-
+25
-
100
150
ns
60
100
ns
12
-
ns
60
-
pC
72
-
dB
-90
-
dB
Source OFF Capacitance, CS(OFF)
f = 1MHz, VS = VD = 0V (Figure 7)
+25
-
12
-
pF
Drain OFF Capacitance, CD(OFF)
+25
-
12
-
pF
Channel ON Capacitance, CD(ON) + CS(ON)
+25
-
39
-
pF
DIGITAL INPUT CHARACTERISTICS
Input Current with VIN Low, IIL
VIN Under Test = 0.8V, All Others = 2.4V Full
-1
0.005
1
μA
Input Current with VIN High, IIH
VIN Under Test = 2.4V, All Others = 0.8V Full
-1
0.005
1
μA
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
Drain-Source ON Resistance, rDS(ON)
V+ = 13.5V, V- = -13.5V,
IS = 10mA, VD = ±10V
Full
-15
-
+25
-
20
Full
-
-
15
V
45
Ω
55
Ω
rDS(ON) Matching Between Channels, ΔrDS(ON) V+ = 16.5V, V- = -16.5V,
IS = -10mA, VD = 5, 0, -5V
+25
-
3
3
Ω
Full
-
-
5
Ω
Source OFF Leakage Current, IS(OFF)
V+ = 16.5V, V- = -16.5
VD = ±15.5V, VS = 15.5V
+25
-0.5
-0.01
0.5
nA
Full
-5
-
5
nA
Drain OFF Leakage Current, ID(OFF)
+25
-0.5
-0.01
0.5
nA
Full
-5
-
5
nA
Channel ON Leakage Current, ID(ON) + IS(ON) V± = ±16.5V, VD = VS = ±15.5V
+25
-1
-0.04
1
nA
Full
-10
-
10
nA
3
FN3284.11
November 20, 2006
 ▷