English
Language : 

CD22M3494_06 Datasheet, PDF (3/8 Pages) Intersil Corporation – 16 x 8 x 1 BiMOS-E Crosspoint Switch
CD22M3494
Absolute Maximum Ratings
DC Supply Voltage (VDD)
Voltages Referenced to VEE . . . . . . . . . . . . . . . . . . . . -0.5 to 16V
DC Supply Voltage (VDD)
Voltages Referenced to VSS . . . . . . . . . . . . . . . . . . . . . -0.5, 16V
DC Input Diode Current, IIN
For VI, Digital < VSS -0.5V or VI,
Analog < VEE -0.5V or VI > VDD 0.5V . . . . . . . . . . . . . . . . . . . . ±20mA
DC Output Diode Current, IOK
For VO, Digital < VSS -0.5V or VO,
Analog < VEE -0.5V or VO > VDD 0.5V . . . . . . . . . . . . . . . . . . . ±20mA
DC Transmission Gate Current . . . . . . . . . . . . . . . . . . . . . . . . . . ±25mA
Power Dissipation Per Package (Po)
For TA = -40°C to 85°C (PDIP). . . . . . . . . . . . . . . . . . . . . .500mW
For TA = 60°C to 85°C Derate Linearly . . . . . . .12mW/°C to 200mW
For TA = -40°C to 85°C (PLCC) . . . . . . . . . . . . . . . . . . . . . . .600mW
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (°C/W)
PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
PLCC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
43
Maximum Junction Temperature Plastic Package . . . . . . . . . . 150°C
Maximum Storage Temperature Range (TSTG). . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C
(PLCC - Lead Tips Only)
*Pb-free PDIPs can be used for through hole wave solder processing
only. They are not intended for use in Reflow solder processing.
applications.
Operating Conditions
Operating Temperature Range (TA)
Package Type E and Q . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
Supply Voltage Range
For TA = Full Package Temperature Range
VSS = 0V, VEE = 0V, VDD . . . . . . . . . . . . . . . . . . . . . . . 4V to 15V
DC Input or Output Voltage VI or VO . . . . . . . . . . . . . . . VEE to VDD
Digital Input Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . VSS to VDD
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications TA = -40°C to 85°C, VDD = 5V, VSS = 0V, VEE = 0V, Unless Otherwise Specified
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
STATIC CONTROLS
Supply Current
High-Level Input Voltage
IDD
VDD = 5V, Logic Inputs = VDD
VDD = 15V, Logic Inputs = VDD
VIH
VDD = 5V
-
-
-
-
2.4
-
(Note 2)
Low-Level Input Voltage
VIL
-
-
Input Leakage Current, Digital
IIN
Reset = Low (Note 3)
-
-
MAX
UNITS
2
mA
5
mA
-
V
0.8
V
(Note 2)
±10
µA
(Note 4)
Electrical Specifications TA = -40°C to 85°C, VDD = 12V, VSS = 0V, VEE = 0V, Unless Otherwise Specified.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
STATIC CROSSPOINTS
ON Resistance
rON
VSS = VEE = 0V,
VDD = 10V
-
40
TA = 25°C, VIN = VDD/2, VX
- VY = 0.2V
VDD = 12V
-
36
ON Resistance
Difference in ON Resistance
Between Any Two Switches
rON
TA = -40°C to 85°C,
VDD = 10V
-
50
VIN = VDD/2, VX -VY = 0.2V,
VSS = VEE = 0V
VDD = 12V
-
45
∆rON
TA = 25°C, VIN = VDD/2, VX - VY = 0.2V,
-
6
VSS = VEE = 0V, VDD = 12V
MAX UNITS
75
Ω
65
Ω
75
Ω
65
Ω
10
Ω
3
FN2793.7
January 16, 2006