ISL28417_14 Datasheet, PDF (26/34 Pages) Intersil Corporation – 40V Precision Low Power Operational Amplifiers

ISL28117, ISL28217, ISL28417
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make
sure you have the latest Rev.
DATE
REVISION
CHANGE
September 11, 2012
FN6632.10
Feature on Page 1: Added No phase reversal.
Removed from ordering information QFN parts ISL28417FRZ (not release part) on Page 2 .
Removed all instances of QFN through document (front page, table of contents, thermal information, pin
description and POD.
Added to the typical performance curves table figure 53 on page 19: Common mode input impedance.
February 23, 2012
FN6632.9
“Ordering Information” on page 2:
Removed “Coming soon” from ISL28417FVZ and changed Part Marking column from "28417 FVZ" to
28417 FVZ-C". Changed "-40 to +125" to "200 C-grade”
Added new Part Number ISL28417 FVBZ
Electrical Spec changes:
VOS Description Section: page 6 & page 8: Changed “Input Offset Voltage; SOIC Package” to Input Offset
Voltage; SOIC, TSSOP Package”
TCVOS Description section: page 7 & page 9: Changed;Input Offset Voltage Temperature Coefficient; SOIC
Package to Input Offset Voltage Temperature Coefficient; SOIC, TSSOP Package
February 10, 2012
TCIOS Conditions section: page 7 & page 9: Changed "ISL28417 SOIC B and C Grade” to "ISL28417 SOIC, TSSOP
B and C Grade”.
“Ordering Information” on page 2:
Updated Pkg. Dwg. # for ISL28117FUBZ, ISL28117FUZ, ISL28217FUBZ & ISL28217FUZ from M8.118 to
M8.118B
Updated Pkg. Dwg. # for ISL28117FRTBZ, ISL28117FRTZ, ISL28217FRTBZ & ISL28217FRTZ from L8.3x3A to
L8.3x3K
Updated Pkg. Dwg. # for ISL28417FRZ from L16.4x4 to L16.4x4E
“Thermal Information” on page 6:
Added Θ_JA and Θ_JC for 16 Ld QFN and 14 Ld TSSOP
Figure 52, “% OVERSHOOT vs LOAD CAPACITANCE, VS = ±15V” on page 18:
X-Axis (Capacitance pF) values 1k and 10k were shifted 1 decade to the right. Shifted 1 decade to the left and
added new label "100k" at the extreme right (where the "10k" value was located).
Added dual and quad to the “SPICE NET LIST” on page 23.
“Package Outline Drawing (M8.118B)” on page 31:
Changed from M8.118 to M8.118B
Top View:
Package width & height changed from 3.0±0.05 to 3.0±0.1
Package height from lead to lead changed from 4.9±0.15 to 4.9±0.2
Side View 2:
Lead thickness changed from 0.09-0.20 to 0.15±0.05mm
Side View 1:
Package height changed from 0.85±0.10 to 0.86±0.05
Changed lead width from 0.25-0.036 to 0.23-0.36
Detail X:
Foot of lead length changed from 0.55±0.15 to 0.53±0.10
“Package Outline Drawing (L8.3x3K)” on page 32:
Changed from L8.3x3A to L8.3x3K
Bottom View:
Changed lead height from 0.3±0.1 to 0.4±0.05
Changed lead width from 0.30±0.05 to 0.25±0.05
Land Pattern:
Changed lead width from 0.30 to 0.25
26
November 30, 2012
FN6632.10