ISL55015_14 Datasheet, PDF (2/6 Pages) Intersil Corporation – MMIC Silicon Bipolar Broadband Amplifier

ISL55015
Absolute Maximum Ratings (T_A = +25°C)
Supply Voltage from VSP to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V_S+ +0.3V to GND -0.3V
Ambient Operating Temperature . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +125°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .+135°C
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . . . . . 6000V
Machine Model (Per EIAJ ED-4701 Method C-111) . . . . . . . . . . . . . 250V
Thermal Information
Thermal Resistance (Typical)
θ_JA (°C/W) θ_JC (°C/W)
6 Ld SC-70 (Notes 4, 5) . . . . . . . . . . . . . . . . 255
195
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. θ_JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
5. For θ_JC, the “case temp” location is taken at the package top center.
Electrical Specifications V_SP = +5V, Z_RSC = Z_LOAD = 50Ω, T_A = +25°C, 24Ω V_SP to OUT, unless otherwise specified.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
MAX
(Note 6) TYP (Note 6) UNIT
Vsp
Supply Voltage
To operate below 5V, the 24Ω resistor to supply
3.0
should be reduced
5.5
V
Gt
Small Signal Gain
1.0GHz
12.3 13.5 14.8
dB
1.5GHz
11.7 13.3 14.2
dB
2.0GHz
11
12.4 13.5
dB
P1dB
Output Power at 1dB Compression
1.0GHz
16.4 18.1 21.6 dBm
2.0GHz
15.3 19.4 21.0 dBm
OIP3
Output Third Order Intercept Point
1.0GHz
31.3
dBm
2.0GHz
28.4
dBm
OIP2
Output Second Order Intercept Point Input tones at 1.0GHz and 1.1GHz, at Input
Power = -15dBm, Output tone 2.1GHz
47
dBm
BW
3dB Bandwidth
3dB below Gain @ 500MHz
2.9
GHz
IRL
ORL
RISOL
Input Return Loss
Output Return Loss
Reverse Isolation
1.0GHz Z_RSC = 75Ω, Z_LOAD = 50Ω
1.0GHz Z_RSC = 75Ω, Z_LOAD = 50Ω
2.0GHz
20.2
dB
21.4
dB
18.9
dB
NF
Noise Figure
2.0GHz
4.8
dB
ID
Device Operating Current
54
62.5
69
mA
NOTE:
6. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
2
FN6284.2
February 19, 2013